Force Measurement Module features plug and play operation.

Force Measurement Module features plug and play operation.

With rugged aluminum housing, RG smart load cell is designed for integration in to assembly systems, weighing systems, and process automation and testing automation applications. It is controlled by commands sent from PC/PLC thru its RS-232 connector. Device has ASCII command library that allows for functions including peak force recall, set points, data averaging, data filtering, and...

Read More »
Signal Level Meter targets CATV applications.

Signal Level Meter targets CATV applications.

Designed for installation and testing of CATV systems, model A0500013 is used to measure parameters such as TILT, C/N, and trunk cable voltage. It can display 2 channels simultaneously, and test results clearly with large character TN LCD screen. Product tests CATV signal levels in both channel and frequency modes, and helps maintain digital, analog or bilateral networks.

Read More »
Dual Gauge prevents deep battery discharge.

Dual Gauge prevents deep battery discharge.

By preventing battery from dipping below specified state of charge, Battery Discharge Indicator and Hour Meter Dual Gauge helps optimize battery life. Lockout gauge version uses internal relay to shutdown battery, while lift-lockout version allows lift equipment to cycle down to bottom of range before locking out of battery. Both fully sealed units prevent operator from continuing to use...

Read More »
Noise Measurement Kit suits difficult applications.

Noise Measurement Kit suits difficult applications.

Along with DSP and color LCD, CEL-620.A offers all components needed for occupational hygienists to conduct various noise measurement surveys. It provides broadband meter features while simultaneously allowing user to perform real-time measurements in octaves from 16 Hz to 16 kHz and third octaves from 12.5 Hz to 20 kHz. Meter is suited for difficult situations, such as those encountered with...

Read More »

Optical Meter is suited for CATV signal level measurements.

Functioning as both optical power tester and signal receiver, model A0500010 measures TILT, C/N, trunk voltage, and spectrum, provides dual wavelength measurements, and scans all channels and stores their signal levels internally. It features large LCD screen allowing TV pictures and measurement results to be viewed simultaneously. Rugged, lightweight, and portable device has rechargeable Lithium...

Read More »

Multipurpose Instrument correlates temperature, voltage.

With up to 48 configurable input channels, MEASURpoint(TM) lets users measure any combination of RTD, thermocouple, and voltage from 300 Â-µV to 400 V. ISO-Channel(TM) technology makes measurements almost indestructible and eliminates any common mode noise and ground loop problems under all environmental conditions. Along with software-selectable voltage ranges on channel basis, features...

Read More »

Optical Multimeter has RS232 interface for data transmission.

Combining functions of optical power meter and light source into single compact unit, Model A0670010 is designed for telecom and CATV maintenance, passive device manufacturing, and for lab testing and research. It features high resolution LCD and allows users to carry out loop-around tests. Each module can also work independently via function switch operation, suited for field-testing. Optical...

Read More »
Water Meters suit commercial and industrial applications.

Water Meters suit commercial and industrial applications.

Series WM Multi-Jet Water Meters feature multijet design that enables accuracy over wide flow ranges, even in low flow applications. Units incorporate magnetically driven, hermetically sealed resistor that will not leak or fog and is completely separated from register system and water. Meters are designed for longevity and maintenance-free operation.

Read More »
Conductivity/TDS/Salinity Meter aids routine quality control.

Conductivity/TDS/Salinity Meter aids routine quality control.

Featuring chemical-resistant, waterproof ABS plastic housing, TraceableÂ-® Conductivity/TDS/Salinity Meter is suited for severe lab or harsh plant environments. Features include Â-½ in. high LCD digits, dual display showing reading and temperature, HOLD button, instant-response probe, solid-state thermistor, and temperature compensation. Measuring 6Â-½ x 1 2/5 x 1Â-¼ in., unit...

Read More »

Power Meter suits construction/maintenance of PON networks.

Featuring auto shut off backlight, real-time display, and rugged waterproof design, model 805 is capable of testing 3 wavelengths of PON network synchronously and testing burst mode signal at 1,310 Nm. It saves 1,000 records, uploads them to management software, and supplies 10 groups of threshold values for selection. Powered by 2,800 mA rechargeable Lithium battery, device offers protected data...

Read More »

All Topics