Direct Drive Motor comes in two parts.
Motors

Direct Drive Motor comes in two parts.

Brushless ULT frameless motor has separate rotor and stator that can be integrated into precision mechanical assemblies. Low profile motor has axial lengths as small as 10 mm, diameters up to 165 mm, and through holes up to 120 mm, making it suitable for direct drive rotary applications. Models are available with 30 to 600 oz-in of torque output. Its three phase motor will run on any sinusoidal...

Read More »
Chains

Lube-free Chain exceeds ANSI specs.

Xceeder Chain has oil-impregnated felt seals that keep dirt out and lubrication in for increased wear life. Drive, conveyor, and attachment chains are available in sizes 40 to 100, are interchangeable with ANSI standard chain, and work with standard sprockets. They handle same maximum loads as ANSI standard chain, and exceed ANSI minimum tensile strength requirements.

Read More »
Servomotor eliminates dithering.
Motors

Servomotor eliminates dithering.

SilverMax 34HC has Anti-Hunt mode which eliminates servo dithering and allows motor to remain motionless while maintaining target position. Motor has 3200 in.-oz of torque, maximum power of 600 W, and is available in 4 stack lengths. System combines motor, controller, driver, encoder, serial communications and 7 configurable I/O. It can be programmed for applications requiring electronic clutch,...

Read More »
Efficient Motor is for process industry applications.
Motors

Efficient Motor is for process industry applications.

M3000 motor qualifies for highest European efficiency class (eff1). Improved cooling doubles life of bearings and windings, gives longer component life and protects motor from overheating, even when covered with dust. Large terminal box and terminal board enable easy installation. Motors are available in IEC frame sizes 112 to 400 rated at 4 to 710 kW. Cast-iron enclosure is standard for frame...

Read More »
Gearheads and Gearboxes

Gearing Components fit in small enclosures.

Ultra-flat CSD series harmonic drive gearing component sets use S-shaped tooth profile and are 50% shorter than previous CSF series, allowing surrounding enclosure to be made very compact. It has rated torque of 248 in-lb, maximum torque of 673 in-lb, and is available in gear ratios of 50, 100 and 160:1. Applications include robotics, aerospace, and factory automation.

Read More »
Linear Actuator comes with encoder feedback.
Motors

Linear Actuator comes with encoder feedback.

Hybrid linear actuator is available in a variety of resolutions ranging from 0.0003125 to 0.002 in. and thrusts of up to 200 lb. It has compact optical incremental encoder with 2-channel quadrature TTL squarewave outputs. Encoder is available with resolutions ranging from 100 to 2,048 cycles per revolution. Internal monolithic electronic module converts the real-time shaft angle, speed and...

Read More »
Actuator suits conveyor-stop applications.
Actuators

Actuator suits conveyor-stop applications.

Model EFL Aluminum-Extruded Body Air Cylinder features hard coat, anodized, PTFE-impregnated cylinder body. Heavy-duty mounting flange features pilot that contains high-performance iron bearing. Impact load resistance is measured at up to 65 lb at impact velocities of 8 ips. EFL is available with 32 mm bore and offers stroke lengths of 10, 15, 20 and 25 mm. Actuator is available in double-acting...

Read More »
Torque Limiter withstands corrosive environments.
Clutches

Torque Limiter withstands corrosive environments.

H-TLC torque limiter has consistent disengagement, can withstand corrosive environments, and triggers alarms or automatic system shutdown when overload conditions occur. It operates on spring-loaded convex pin and detent that reacts to overloads but not to contaminants like soil, dirt and lubrication. Unit withstands salt, pollutants, mild acids, corrosive moisture of all kinds, and oily...

Read More »
Conveyor Belts have insert rollers for better turns.
Belts

Conveyor Belts have insert rollers for better turns.

Insert rollers on Series 2400 radius belts enable low back pressure accumulation around turns with ratios of 2.8 and 1.7. Belts have gray acetal rollers located directly on belt rods. They protrude beyond top and bottom of belt, allowing manipulation of product speed to belt speed. Belts are available in white and gray polypropylene and white and blue acetal. They are built in widths from 6.0 in....

Read More »
Hybrid Linear Actuators use lifetime lubricant.
Actuators

Hybrid Linear Actuators use lifetime lubricant.

Hybrid Linear Actuators utilize high performance synthetic grease, with no need to reapply lubrication. Nonflammable, chemically inert, low vapor pressure lubricant has temperature characteristics ranging from -65°C to 250°C. Actuators are available with resolutions from 0.000060 in. per step to 0.002 in. per step, deliver thrust of up to 200 lb, and can exceed speeds of 10 ips.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers