Washdown Motors resist rust and corrosion.

Paint free motors are offered in 1/2, 3/4, 1, 1-½, and 2 HP, and operate at 1725 rpm on 208-230/460 Vac power. NEMA 56 HC frames are available for motors with ratings of 1/2 through 1 HP, and NEMA 145TC frames are matched with 1 through 2 HP rated motors. Washdown motors resist water entry and drain condensation via their VBX INPRO/SEAL® shaft seal, T drains, and nitrile conduit box gasket with...

Read More »
Transaxle features wound field motor.

Transaxle features wound field motor.

Model T523 DC Motor Transaxle incorporates cut steel helical gearing and splined interface between motor and transaxle. Axle shafts include oil seals that resist penetration of dirt. Transaxle features ball bearing construction, all aluminum housing, and neoprene mounting sleeves. Motors range from 12 through 48 Vdc and produce up to 2 hp. Gear ratios of 8.2:1, 11.1:1, 15.9:1, 23.2:1, and 29.4:1...

Read More »
AC Motor operates in severe environments.

AC Motor operates in severe environments.

Totally enclosed ac permanent split capacitor motor features clamshell housing, liquid-tight connectors, cast aluminum capacitor cover, heavy duty ball bearings, and steel shafts. Face-mount unit is available in power ratings of 1/4, 1/3, and 1/2 hp at 115 or 230 V in 50 or 60 cycle ac. Two-pole electrical design provides electrical current for both clockwise and counterclockwise directions at...

Read More »

Linear Actuator Series suits positioning applications.

Totally enclosed Digit-HT linear actuator series provides up to 440 lbs. of force using 35 Vdc driver at 1.7 to 3.4 A. Available in 2, 4, and 8 in. stroke lengths, and moving at up to 14 in./sec, in-line linear actuator series offers repeatability of 1.5 microns. Mounting options include rod bearing clevises, trunnion mounts, and brackets. Precision ball and Acme drive screws are directly coupled...

Read More »
Electric Linear Actuator suits harsh environment applications.

Electric Linear Actuator suits harsh environment applications.

Kodiak(TM) K2 electric actuator series can lift or move loads of up to 2,000 lbs. Its operating speed ranges from 0.5 to 2.4 ips at rated loads, and stroke length varies from 4 to 18 in. Available with various mounting configurations, actuator series has ball bearing supported extension rod that tolerates misalignment and side load. Construction includes O-rings, heavy-duty wiper seals, and TGIC...

Read More »

Precision Turbine incorporates governed design.

Dotco® 12R91 series precision turbine allows tool to idle and provides full power under load. Pre-loaded bearings maintain stability in spindle to allow for smoother cuts. Available with 3 mm and 1/8 in. collets, 65,000 rpm rear exhaust governed tool suits applications that previously used 100,000 rpm non-governed tools. It is available in models with 2 and 4 ft overhose to direct exhaust away...

Read More »
Bearings improve machine tool performance.

Bearings improve machine tool performance.

Fafnir® THSS True High-Speed Sealed bearings are angular contact ball bearings designed for high spindle speeds. Non-contact dynamic seals keep contamination out while minimizing running torque, and effectively retaining grease inside bearing. Fafnir WearEver(TM) bearings resist contamination-induced surface damage. They feature CERBEC® ceramic ball and steel that resists wear debris and hard...

Read More »
Brushless Motor survives hostile environments.

Brushless Motor survives hostile environments.

Dustproof Series brushless motor and resolver forms single component that completely locks out contamination, making unit suitable for hostile environments. Drive electronics can be removed, allowing motor to be controlled via RS232 communication. When combined with drive system, motors are suitable for closed-loop motion control applications. Motors are available in frame sizes from 3.25 to 7.5...

Read More »

Replacement Motors fit blower and condenser fans.

Masterfit multiple hp motors are easily and quickly adapted on-site, using combination of speed taps and capacitors. Line includes FD6000 and FDL6001 blower motors for 115 or 208-230 V, 1075 rpm applications from 1/6 to 1/2 hp; and model FSE6000 condenser fan motor, for 208-230 V, 1075 rpm applications from 1/6 to 1/3 hp.

Read More »

Single Phase Motor replaces Liebert air conditioning units.

Model C663 is direct replacement for Liebert model B-095D condenser motor, Johnstone part number S89-084, and Emerson part number K63HXEF4-4599. Single shaft motor is suited for 208-230/460 V 60 Hz, 1100 rpm applications at -¾ hp, or 50 Hz applications requiring 190/380 V, 925 rpm replacement motor. Motor includes capacitor and rainshield for protection in rugged weather conditions, and is...

Read More »

All Topics