New: Buy Now on Thomas and Pay Over Time with Credit Key   Learn More

Gearbox offers maximum output torque of 796,500 lb-in.

Gearbox offers maximum output torque of 796,500 lb-in.

Clincher(TM) Parallel Shaft-Mount Gearbox SK 12382 triple-stage geared motor is available with either solid or hollow output shaft. Construction features include UNICASE(TM) one-piece housing, gearing designed to AGMA CLASS 13 standards, Quadrilip(TM) oil sealing system, and autovent sealing. Operational efficiency is rated at 98.5%. Power ranges from 15 to 200 hp, output speeds vary from 8.7 to...

Read More »
Planetary Gearboxes mount directly to servomotors.

Planetary Gearboxes mount directly to servomotors.

GTM Planetary Gearboxes' range and modular construction make them suitable for use in factory automation applications. Taper bearings act as pumps, minimizing oil used in vertical, horizontal, or angled applications. Cold-fusion process between coupling and sun gear allows emergency stop torque for safety and reliability. GTM specifies 1,000 emergency stops before loss of accuracy.

Read More »
DC Motors/Gearmotors feature skewed armatures.

DC Motors/Gearmotors feature skewed armatures.

LO-COG-® Series 8000 brush-commutated DC motors and gearmotors feature 7-slot skewed armatures designed to minimize magnetic cogging. Motors are available in 3 lengths and can achieve peak torques up to 16.8 oz-in. and speeds to 10,650 rpm. Gearmotors are offered in 3 lengths with 11 ratios from 6.3:1 to 1803.6:1 and can achieve peak torques to 100 oz-in. (standard) or 160 oz-in. (with...

Read More »
Stepping Motor offers integrated motion control.

Stepping Motor offers integrated motion control.

NEMA size 23 stepping motor, MDrive23, offers on-board +12 to +48 V microstepping drive and programmable MDrive 23 motion control. Features include four 5 to 24 V general purpose I/0 lines, one 10 bit analog input, and 0 to 5 MHz step clock rate. Microstep resolution is rated up to 51,200 steps per revolution. MDrive23 Motion Control communicates over RS485, and baud rates range from 4,800 to...

Read More »

Pully Drive System integrates with linear module applications.

LPB integrated geared pulley drive system is available in sizes from 70 to 120 mm with ratios of 1:1, 3:1, 5:1, and 10:1. Gearbox has flange output, allowing it to be nested inside pulley, eliminating need for right angle gearbox, couplings and/or additional bearings. LPB design increases radial load capacity associated with belt and pulley applications, greatly increasing output bearing life.

Read More »
Software facilitates set up of linear and rotary actuators.

Software facilitates set up of linear and rotary actuators.

proTern(TM) software is designed for Ternary linear and rotary actuator system. With Ternary, any of 16 specific positions can be defined via software, then achieved with absolute accuracy. proTern provides real numerical data for position, velocity, acceleration, deceleration, and force/torque commands using PC or handheld PDA. Ternary is available in 46 mm frame size, with stroke lengths of 25...

Read More »
Gearboxes feature modular construction and quiet operation.

Gearboxes feature modular construction and quiet operation.

GTM Planetary Gearboxes mount directly to servomotors and have small internal cavity that reduces noise. Large taper bearings act as a pump, minimizing amount of oil used in vertical, horizontal, or angled applications. Cold-fusion process between coupling and sun gear allows high emergency stop torque for maximum safety (1,000 emergency stops before loss of accuracy).

Read More »
Valves and Actuators fit into bus networks.

Valves and Actuators fit into bus networks.

Line of modulating valve packages and automated on-off valves can be integrated with control valves and other devices on bus network. Valve line includes: Jamesbury and Neles screwed-end ball valves, flanged ball valves, high-performance butterfly valves, rotary control valves and special and severe service valves and accessories. Actuator line includes Jamesbury, Neles, and Valvcon actuators.

Read More »
Motor suits mild nuclear environments.

Motor suits mild nuclear environments.

Reliance-® motor meets IEEE-334-1994 requirements and is available in 1E-Safety Related or non-1E classification. It features cast iron construction, including frame, end brackets, and bearing inner caps, as well as zinc-plated hex head hardware, stainless T-drains, and severe-duty TEFC-XEX enclosure. Class H insulation system is supplied for extended thermal life.

Read More »
3Sixty Mission Critical Launches New Service Offering UPS as a Service As A Cost Effective Alternative to UPS Equipment Ownership
Sponsored

3Sixty Mission Critical Launches New Service Offering UPS as a Service As A Cost Effective Alternative to UPS Equipment Ownership

At 3Sixty Mission Critical, we specialize in maintaining the performance and uptime of our customer's mission-critical applications. Our services are comprehensive and designed to take on the entire burden of maintenance. Our "UPS as a service" is just another example of how we develop out of the box solutions to help our customers operate more efficiently; see our video to earn more.

Read More »

All Topics