Drive Chain reduces workplace noise.
Chains

Drive Chain reduces workplace noise.

Low Noise Drive Chain offers spring roller construction, which absorbs impact of sprocket-chain interaction, reducing equipment noise by up to 10 decibels. It is available in sizes 40 through 80, and can directly replace ANSI standard chain for compliance with environmental management standards such as ISO 14000. Chain exceeds ANSI minimum tensile strength requirements and operates with standard...

Read More »
Servo Actuator has output speeds from 30-80 rpm.
Actuators

Servo Actuator has output speeds from 30-80 rpm.

PowerHub(TM) hollow shaft servo actuator delivers positional accuracy less than 1 arc min and repeatability of +/- 5 arc sec. Center through holes are available up to 27mm, allowing vacuum lines and wiring to be run through center of unit to external devices. Actuator is available in 2 sizes (-20 and 25) with ratios from 50:1. Output flange is supported by precision bearings, and output torques...

Read More »
Front End Brakes offer IP65 protection.
Brakes

Front End Brakes offer IP65 protection.

Available for NEMA 23 and 34 sizes and designed specifically to plug in to Stepper or Servo Motors, SSB Series incorporates zero backlash permanent magnet brake and torsionally rigid coupling to accept misalignment. Brakes are also available in NEMA 42 size offering IP65 splashproof and dustproof protection. All 6 models include dual preloaded sealed bearings and black anodized aluminum housing.

Read More »
Linear Bearing needs no lubricants.
Bearings

Linear Bearing needs no lubricants.

One-Stop Shopping DryLin(R) linear bearing system consists of polymer-lined plain bearings with or without pillow blocks and DryLin(R) S aluminum shafting. It is suited for applications where lubricants are not desired, and wherever contamination due to dirt, dust, sawdust, lint or paper dust hinders operation of linear ball bearings.

Read More »
Motors

Stepper Motors have chrome platens.

Linear stepper motors travel at speeds to 80 in./sec, with strokes to 144 in. and acceleration to 1G. 2- and 4-phase linear steppers are capable of up to 50 lbs continuous force and 65 lbs peak force. Resolution of 2-phase motors is 1 full step equals .010 in., and 1 microstep equals .00004 in. Resolution of 4-phase motors is 1 full step equals .005 in., and 1 microstep equals .00002 in. Motors...

Read More »
Clamping Cylinder loads and unloads light parts.
Actuators

Clamping Cylinder loads and unloads light parts.

Twist Clamp has internal mechanism to produce rotary piston motion throughout stroke. By attaching clamp arm, actuator becomes clamping mechanism for light-duty holding applications. Motion rotates clamp arm out of work area for easy loading and unloading of parts. It uses 40mm bore cylinder that produces up to 224 lb of clamping force at maximum pressure of 140 psi. Cylinder body is hard coat...

Read More »
Linear Bearings are made from 100% polymer.
Bearings

Linear Bearings are made from 100% polymer.

Drylin® RJI inch and Drylin® RJM metric polymer linear bearings are directly interchangeable with standard re-circulating ball bearings, and fit into standard pillow blocks. Made from iglide® J material, bearings have low coefficient of friction and shock and vibration dampening, require no external lubrication, and resist corrosion and wear. They are available from stock in...

Read More »
Dustproof Motor locks out contamination.
Motors

Dustproof Motor locks out contamination.

Abrasive Dustproof Series, sealed with built-in o-rings, has air fittings for pressurization up to 15 psi. Shaft slinger prevents abrasive dust from attacking shaft seal material, which in turn prevents dust from entering bearing. Motor is available in standard 23, 34, 42 and 65 frame sizes. Applications include industrial operations that use, produce or process powdered materials such as fiber...

Read More »
Speed Reducers withstand corrosive environments.
Gearheads and Gearboxes

Speed Reducers withstand corrosive environments.

All-Stainless Steel Speed Reducers, with horsepower ranges through 5 HP, are available in frame sizes 918, 921, and 926 with quill-type 56C, 140TC, and 180TC NEMA C-face inputs. Construction consists of 304 cast stainless steel housings, covers, and shafts; stainless steel hardware; O-ring sealed C-face; and Mobile SHC 634 synthetic lubrication. Pressure compensation chamber prevents internal...

Read More »
Linear Actuators can be custom configured.
Actuators

Linear Actuators can be custom configured.

Electromechanical CATR actuators can be built using standard components such as motors, gears, screws, controls, and attachments to perform opening/closing, clamping/gripping, raising/lowering, or pushing/pulling functions. CATR 33 has ACME sliding screw for standard operation, CATR 33H has ACME screw, and CATR 32B has Ball screw. Options include stroke lengths, ac or dc motors, and friction...

Read More »
Precision Fabricating with Over 40 Years of Experience
Sponsored

Precision Fabricating with Over 40 Years of Experience

Quality Sheet Metal specializes in delivering precision, value, and customer service. With a client base that spans many diverse industries and a reputation for excellence that goes back over four decades, our clients know that we can provide the optimal combination of value and flexibility regardless of the challenge. See our video to learn what we can do for you. Through investments in state-of-the-art design, manufacturing, and quality control systems, Quality Sheet Metal remains focused on maintaining a high standard of quality, customer service, and competitive pricing. With an emphasis on customer satisfaction, Quality Sheet Metal is dedicated to establishing long-term partnerships, similar to the ones they currently have with their valued clients. If you're looking for a new partner with extensive capabilities in sheet metal fabricating and finishing, look no further.

Read More »

All Topics