Ball Valves and Actuators suit severe duty applications.
Valves

Ball Valves and Actuators suit severe duty applications.

Trunion style ball valves and actuators are specifically designed for shut-off of liquid and gas flow up to 20,000 psi. Two 3-way and 3-way diverter ball valve configurations are available in orifices of .187 or .375 in. Valves incorporate 316 stainless steel construction, Viton 0-rings, Arlon ball seats and peek bearing washers. They have 1 1/16 in. dia hole for panel mounting. Air-operated...

Read More »
DC Motor is suited for light duty belt conveyors.
Motors

DC Motor is suited for light duty belt conveyors.

Micro-Motor 24V brushless DC geared motor has right angle design that fits into 2 3/4 in. conveyor frame. Gearbox transfers 99% of motor output power to belt drive pulley. Driver card controls and activates motor allowing varying conveyor speed and change of travel direction. Micro-Motor has torque rating up to 112 in. lbs and can drive 1.9, 2.25 or 2.5 in. belt drive pulleys. Drive system moves...

Read More »
Gearheads incorporate clamping style input pinion.
Gearheads and Gearboxes

Gearheads incorporate clamping style input pinion.

MRP all-planetary, low-backlash, servo-grade gearheads are available in 1 or 2 stages with ratios up to 100:1. Five sizes are offered: MRP-050, 070, 090, 120 and 155, which range from 2 to 6.1 in. square. Backlash specification is 10 to 15 arc-mins max depending upon gearhead size and number of gear stages. MRP round body gearhead has tapped holes in face of output shaft end, and square flange on...

Read More »
Solids Reduction Unit retrofits to twin shaft grinders.
Bearings

Solids Reduction Unit retrofits to twin shaft grinders.

Annihilator twin shaft solids reduction unit is supplied with seals and bearings housed in replaceable stainless steel cartridge, which allows on-site replacement. Counter-rotating, hexagonal shaft design coupled with hardened steel cutters provide maximum shredding strength necessary to process 300 to 4,250 GPM of influent. Annihilator is fitted with toothed cutting spacers, electronic control...

Read More »
Failsafe Brake fits stepper and servo motors.
Brakes

Failsafe Brake fits stepper and servo motors.

Model RFEB power-off brake mounts on front end of standard NEMA 23 and NEMA 34 stepper or servo motors to prevent machine from operating or for holding load in place when power fails. It has spring-set design, ball bearing supported output shaft, and operates at speeds to 8,000 rpm. Brake is available in 24 and 90 Vdc versions. Applications include factory automation, material handling, robotics,...

Read More »
Spring Set Brakes hold loads when power fails.
Brakes

Spring Set Brakes hold loads when power fails.

ERD Series electrically-released, spring set brakes perform dynamic stopping and fail-safe, power-off braking to hold loads in event of electrical outage. Brakes are available in 8 sizes, from 3.3 to 9.9 in. dia with torque capacities from 4 to 220 lb ft. Brakes permit stopping and holding in both directions, and can stop loads from motor speeds up to 3600 rpm. Applications include hoists,...

Read More »
Hydraulic Power Unit drives bar shears.
Power Units

Hydraulic Power Unit drives bar shears.

VHPI-3 Hydraulic Power Unit, suitable for use with lightweight Bar Shears, weighs 30 lbs, and can be carried from one location to another. Fluid flow ranges from 1 GPM at low pressure to reduced flow at higher pressure. Its 1/2 HP motor draws 10 amps at 110 Volts.

Read More »
Linear Drive Actuators eliminate friction and backlash.
Actuators

Linear Drive Actuators eliminate friction and backlash.

Series BB 2-piece systems consist of passive, magnet-free, stationary platen, serving as precision linear guideway and moving forcer with built-in roller bearings. All bearings are magnetically preloaded and do not require gap adjustments. Units have force ranges from 5 to 15 lb, open loop motion repeatability of 0.0001 in., and travel length up to 80 in. Forcers are capable of velocities of 60...

Read More »
Protective Sleeves save labor.
Sleeves

Protective Sleeves save labor.

Coated, ballistic Cordura(R) Sidewinder sleeves, with industrial hook and loop closure, allow easy assembly and removal. Sleeves install without disconnecting hydraulic, electrical, and pneumatic hose and cable bundling and can be removed easily for hose maintenance. Material is available in variety of circumferences and bulk lengths to 150 ft for OEM and maintenance operations.

Read More »
Gearing works with standard screw.
Gears

Gearing works with standard screw.

Precision gearing works with threaded long length rods and adapts to rotary or linear motion machinery. It is capable of fine adjustment and positive positioning. Gear is available in variety of standard sizes or can be made to order.

Read More »

All Topics