Planetary Gearboxes mount directly to servomotors.
Gearheads and Gearboxes

Planetary Gearboxes mount directly to servomotors.

GTM Planetary Gearboxes' range and modular construction make them suitable for use in factory automation applications. Taper bearings act as pumps, minimizing oil used in vertical, horizontal, or angled applications. Cold-fusion process between coupling and sun gear allows emergency stop torque for safety and reliability. GTM specifies 1,000 emergency stops before loss of accuracy.

Read More »
DC Motors/Gearmotors feature skewed armatures.
Motors

DC Motors/Gearmotors feature skewed armatures.

LO-COG® Series 8000 brush-commutated DC motors and gearmotors feature 7-slot skewed armatures designed to minimize magnetic cogging. Motors are available in 3 lengths and can achieve peak torques up to 16.8 oz-in. and speeds to 10,650 rpm. Gearmotors are offered in 3 lengths with 11 ratios from 6.3:1 to 1803.6:1 and can achieve peak torques to 100 oz-in. (standard) or 160 oz-in. (with...

Read More »
Stepping Motor offers integrated motion control.
Motors

Stepping Motor offers integrated motion control.

NEMA size 23 stepping motor, MDrive23, offers on-board +12 to +48 V microstepping drive and programmable MDrive 23 motion control. Features include four 5 to 24 V general purpose I/0 lines, one 10 bit analog input, and 0 to 5 MHz step clock rate. Microstep resolution is rated up to 51,200 steps per revolution. MDrive23 Motion Control communicates over RS485, and baud rates range from 4,800 to...

Read More »
Gearheads and Gearboxes

Pully Drive System integrates with linear module applications.

LPB integrated geared pulley drive system is available in sizes from 70 to 120 mm with ratios of 1:1, 3:1, 5:1, and 10:1. Gearbox has flange output, allowing it to be nested inside pulley, eliminating need for right angle gearbox, couplings and/or additional bearings. LPB design increases radial load capacity associated with belt and pulley applications, greatly increasing output bearing life.

Read More »
Software facilitates set up of linear and rotary actuators.
Actuators

Software facilitates set up of linear and rotary actuators.

proTern(TM) software is designed for Ternary linear and rotary actuator system. With Ternary, any of 16 specific positions can be defined via software, then achieved with absolute accuracy. proTern provides real numerical data for position, velocity, acceleration, deceleration, and force/torque commands using PC or handheld PDA. Ternary is available in 46 mm frame size, with stroke lengths of 25...

Read More »
Valves and Actuators fit into bus networks.
Valves

Valves and Actuators fit into bus networks.

Line of modulating valve packages and automated on-off valves can be integrated with control valves and other devices on bus network. Valve line includes: Jamesbury and Neles screwed-end ball valves, flanged ball valves, high-performance butterfly valves, rotary control valves and special and severe service valves and accessories. Actuator line includes Jamesbury, Neles, and Valvcon actuators.

Read More »
Motor suits mild nuclear environments.
Motors

Motor suits mild nuclear environments.

Reliance® motor meets IEEE-334-1994 requirements and is available in 1E-Safety Related or non-1E classification. It features cast iron construction, including frame, end brackets, and bearing inner caps, as well as zinc-plated hex head hardware, stainless T-drains, and severe-duty TEFC-XEX enclosure. Class H insulation system is supplied for extended thermal life.

Read More »
Motors

Washdown Motors resist rust and corrosion.

Paint free motors are offered in 1/2, 3/4, 1, 1Â-½, and 2 HP, and operate at 1725 rpm on 208-230/460 Vac power. NEMA 56 HC frames are available for motors with ratings of 1/2 through 1 HP, and NEMA 145TC frames are matched with 1 through 2 HP rated motors. Washdown motors resist water entry and drain condensation via their VBX INPRO/SEAL® shaft seal, T drains, and nitrile conduit box...

Read More »
Transaxle features wound field motor.
Axles

Transaxle features wound field motor.

Model T523 DC Motor Transaxle incorporates cut steel helical gearing and splined interface between motor and transaxle. Axle shafts include oil seals that resist penetration of dirt. Transaxle features ball bearing construction, all aluminum housing, and neoprene mounting sleeves. Motors range from 12 through 48 Vdc and produce up to 2 hp. Gear ratios of 8.2:1, 11.1:1, 15.9:1, 23.2:1, and 29.4:1...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers