Injection System combines hydraulic and electric technology.
Actuators

Injection System combines hydraulic and electric technology.

PowerShot(TM) Injection System is a sealed, closed-loop actuator that requires no external power unit. Single servomotor controls entire system, including screw rotation of plasticizing screw. Injection and decompression control is accumulator driven, and controlled by servocartridge, which allows closed-loop control of velocity, pressure, and position. Package is installed with few connections...

Read More »
Modular Linear Actuators are custom-built with standard parts.
Actuators

Modular Linear Actuators are custom-built with standard parts.

Corrosion-resistant SKF® CAT33 Modular Range electromechanical linear actuators can be built utilizing standard internal and external components such as motors, gears, screws, controls, and attachments. They perform functions from opening/closing and clamping/gripping to raising/lowering and pushing/pulling. Both right- and left-hand models are available in 3 basic actuator types: CAT33...

Read More »
Brushless Motor provides high speed in miniature package.
Motors

Brushless Motor provides high speed in miniature package.

Electronically commutated model EC 16 offers minimized electrical noise and utilizes high-energy neodymium magnets. Motors are available in 3 versions: with hall sensors, sensorless, or with integrated electronics. Weighing 2 oz, motor has 0.63 in. dia and measures 2.2 in. long, not including shaft or cables. Continuous output power is 40 W, while max speed is 60,000 rpm. Max continuous torque is...

Read More »
Linear Actuator withstands washdown applications.
Actuators

Linear Actuator withstands washdown applications.

Moisture- and corrosion-resistant, stainless steel, pneumatically driven Series CG5 uses FDA-approved grease and materials. Rod scraper minimizes water infiltration to rod seals, and end caps are screwed on. Available with nitrile-rubber or fluoro-rubber seals, series has 1.0 MPa max operating pressure and is available in 8 bore sizes from 20-100 mm with imperial or metric rod end/ports. Piston...

Read More »
Steel Shaft Components suit linear motion applications.
Shafts

Steel Shaft Components suit linear motion applications.

Tubular Steel Shafts are produced from 60 Plus® 52100 material. Pre-drilled and tapped every 8 in., they are available in 1Â-½ and 2 in. diameters in lengths up to 12 ft. Shafts can be supplied fully mounted to support rails as shaft assemblies. They are suitable as conduit for electrical control lines, pressurized air lines for pneumatic devices, or hydraulic lines.

Read More »
Sleeves, Nuts, and Ferrules can hold 5,000 psi.
Nuts

Sleeves, Nuts, and Ferrules can hold 5,000 psi.

Silica SealTight(TM) sleeves, nuts, and ferrules solve problem of connecting capillary tubing to standard 10-32 coned ports intended for 1/16 in. OD tubing. Teflon® FEP sleeves plus PEEK(TM) NanoTight(TM) nuts, and Tefzel® ferrules provide sealing and can be finger tightened to hold 5,000 psi. Twelve color-coded IDs accommodate capillary ODs from 70 Â-µm to 1 mm.

Read More »
Step Motor offers holding torque to 30 oz-in.
Motors

Step Motor offers holding torque to 30 oz-in.

Available in 1.10, 1.38, and 1.54 in. lengths, 0.9Â-º NEMA size 17 High Accuracy motor is capable of holding torque ranges from 12-30 oz-in., depending on length of motor. Product has low inertia, between 0.07-0.13 oz-in.², and is available with unipolar and bipolar windings. Motor is suited for microstepping control and wherever accuracy is critical, as in automation, medical, and...

Read More »
Bearing Controller and Assemblies suit high-speed equipment.
Bearings

Bearing Controller and Assemblies suit high-speed equipment.

Providing bearing stability and precise positioning, MB240 digital control system consists of one 2 A, 40 W system with Adaptive Vibration Control. Custom-built to meet user requirements, Hyperspin spindles are multi-component magnetic bearing assemblies that incorporate radial and thrust bearings, housings, shaft, motor, and controller. Synchronous spindles are offered in speeds to 60,000 rpm...

Read More »
Smart Cylinder suits machine building applications.
Actuators

Smart Cylinder suits machine building applications.

Compliant to ISO 6431 and VDMA 24562 standards within VDMA envelope, smart cylinder contains its own sensors, flow regulators, adjustable cushioning, integrated 5/2 or 5/3 valve, and ASI Bus or Mulitpole fieldbus connections inside the casing. With integrated valve, product achieves top speed of 1.5 m/sec and is available in stroke lengths of up to 1 m. Product requires one electrical and one...

Read More »
Zone Valves and Actuators feature direct-coupled design.
Valves

Zone Valves and Actuators feature direct-coupled design.

Series 599 Zone Valve and Actuator Line offers manual override, visual position indication, and automatic reset after power interruption. Valves have all metal seating surfaces and linear stroke action for tight, secure seal. Units require no tools for installation. Actuator screws onto valve body by hand.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers