DC Motors and Gearmotors suit wet and humid areas.
Motors

DC Motors and Gearmotors suit wet and humid areas.

With max rating of Â-¼ hp @ 2,500 rpm, DC Washguard® products meet IP55 environmental conditions and feature stainless steel or Mirolon 3300 fortified Teflon® output shafts. Motors are offered with face or base mounting. Gearmotors with parallel output shaft have ration options from 5:1 up to 336:1, with full-load torque exceeding 300 in-lbs. Right angle shaft configurations...

Read More »
Brake features internally mounted encoder.
Benders

Brake features internally mounted encoder.

Smart Brake has sealed, hollow shaft incremental encoder that provides continuous feedback for speed, direction, and positioning. Information received from encoder can be fed to PLCs, vector drives, and variable speed controls. Brake is available in torque ratings from 1.5-175 lb-ft to fit NEMA C Face motors from 56C-286TC. Enclosure types include standard, waterproof, washdown, and UL-approved...

Read More »
Roller Pinion provides ball screw alternative.
Gears

Roller Pinion provides ball screw alternative.

Precision Roller Pinion System (RPS) converts rotary motion into backlash-free linear motion. Pinion consists of bearing-supported rollers that move smoothly along face of each tooth. Using segments of rack, system can be configured to any required distance. Accurate positioning speeds are maintained up to 36 fps, while low-friction design does not create heat or wear on components. System may be...

Read More »
Motors

Stepper Motors feature onboard drive electronics.

Series DSM includes NEMA frame sizes 17, 23, and 34, each with 1, 2, or 3 winding stacks. Torque ratings include 32, 60, 74.9, 90, 144, 239, 381, 575 or 1,061 oz-in. The 1.8° stepping motor can be configured for operation in any of 14 step sizes from Â-½-256 micro-steps per full step using Windows® utility and motor-to-PC set-up cable. Chosen setting is stored in non-volatile...

Read More »
AC Induction Motors feature enclosed, waterproof design.
Motors

AC Induction Motors feature enclosed, waterproof design.

Available in 8 standard frame sizes, stainless steel Series WD withstands frequent wetting or washdown. For food service and other washdown applications where motor is not normally submerged, units are supplied with cooling fans. For marine or nuclear applications where submerged motors are cooled by surrounding water, motors are oil-filled and pressure-compensated. Custom versions for use in...

Read More »
Actuators

Scotch Yoke Actuators offer torques up to 600,000 lb-in.

Capable of operating ball, butterfly, and plug valves, dampers, or louvers, TRIAC THD Series features symmetrical yoke that delivers max torque at both ends of 90° cycle. Units come in 12 sizes, each available in spring-return or double-acting versions with operating pressures from 40-125 psig. Temperature-rated from -20 to 180°F, actuators feature travel stop adjustment of...

Read More »
Brush/Brushless Servo Motors feature low torque ripple.
Motors

Brush/Brushless Servo Motors feature low torque ripple.

Series SE500 consists of 8 brushed servos from 23-500 W, while Series SE600 features 8 low inertia brushless servos from 30-1,500 W, and Series SE700 includes 12 medium inertia brushless servos from 50-7,000 W. Differential Hall signals U, V, and W are standard on SE600 and SE700 units. Torque ripple on these 10-pole servos is 0.3% of rated torque. Series SE500 features 1,000 line differential...

Read More »
Linear Actuators include 5-phase hybrid stepping motor.
Actuators

Linear Actuators include 5-phase hybrid stepping motor.

Available with and without anti-rotation guide mechanism, miniature Series DRL comes in 1.1, 1.65, and 2.36 in. sq frame sizes. Actuators use rolled ball screw or ground ball screw and produce 6.7, 22, or 66 lb of force over 1.18, 1.57, or 1.97 in. stroke. Repetitive positioning accuracy is ±0.00039 to ±0.00079 in. Microstepping drivers provide up to 2 A at 24 Vdc to achieve nominal...

Read More »
Turbines

Gas Turbine Combustion System reduces NOx emissions.

Dry Low NOx combustion system reduces NOx emissions for company's 12 MW class 10-2 gas turbine from 25 to 15 ppm. Emissions level is guaranteed over operating conditions spanning 50-100% of load and ambient temperature range of -20° to +100°F. It requires no catalytic hardware minimizing number of combustion parts. Combustion chamber incorporates 4 GE5 premixed pilot burners and...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers