DC Motors/Gearmotors feature skewed armatures.

DC Motors/Gearmotors feature skewed armatures.

LO-COGÂ-® Series 8000 brush-commutated DC motors and gearmotors feature 7-slot skewed armatures designed to minimize magnetic cogging. Motors are available in 3 lengths and can achieve peak torques up to 16.8 oz-in. and speeds to 10,650 rpm. Gearmotors are offered in 3 lengths with 11 ratios from 6.3:1 to 1803.6:1 and can achieve peak torques to 100 oz-in. (standard) or 160 oz-in. (with...

Read More »
Stepping Motor offers integrated motion control.

Stepping Motor offers integrated motion control.

NEMA size 23 stepping motor, MDrive23, offers on-board +12 to +48 V microstepping drive and programmable MDrive 23 motion control. Features include four 5 to 24 V general purpose I/0 lines, one 10 bit analog input, and 0 to 5 MHz step clock rate. Microstep resolution is rated up to 51,200 steps per revolution. MDrive23 Motion Control communicates over RS485, and baud rates range from 4,800 to...

Read More »

Pully Drive System integrates with linear module applications.

LPB integrated geared pulley drive system is available in sizes from 70 to 120 mm with ratios of 1:1, 3:1, 5:1, and 10:1. Gearbox has flange output, allowing it to be nested inside pulley, eliminating need for right angle gearbox, couplings and/or additional bearings. LPB design increases radial load capacity associated with belt and pulley applications, greatly increasing output bearing life.

Read More »
Software facilitates set up of linear and rotary actuators.

Software facilitates set up of linear and rotary actuators.

proTern(TM) software is designed for Ternary linear and rotary actuator system. With Ternary, any of 16 specific positions can be defined via software, then achieved with absolute accuracy. proTern provides real numerical data for position, velocity, acceleration, deceleration, and force/torque commands using PC or handheld PDA. Ternary is available in 46 mm frame size, with stroke lengths of 25...

Read More »
Gearboxes feature modular construction and quiet operation.

Gearboxes feature modular construction and quiet operation.

GTM Planetary Gearboxes mount directly to servomotors and have small internal cavity that reduces noise. Large taper bearings act as a pump, minimizing amount of oil used in vertical, horizontal, or angled applications. Cold-fusion process between coupling and sun gear allows high emergency stop torque for maximum safety (1,000 emergency stops before loss of accuracy).

Read More »
Valves and Actuators fit into bus networks.

Valves and Actuators fit into bus networks.

Line of modulating valve packages and automated on-off valves can be integrated with control valves and other devices on bus network. Valve line includes: Jamesbury and Neles screwed-end ball valves, flanged ball valves, high-performance butterfly valves, rotary control valves and special and severe service valves and accessories. Actuator line includes Jamesbury, Neles, and Valvcon actuators.

Read More »
Motor suits mild nuclear environments.

Motor suits mild nuclear environments.

RelianceÂ-® motor meets IEEE-334-1994 requirements and is available in 1E-Safety Related or non-1E classification. It features cast iron construction, including frame, end brackets, and bearing inner caps, as well as zinc-plated hex head hardware, stainless T-drains, and severe-duty TEFC-XEX enclosure. Class H insulation system is supplied for extended thermal life.

Read More »

Washdown Motors resist rust and corrosion.

Paint free motors are offered in 1/2, 3/4, 1, 1Â-½, and 2 HP, and operate at 1725 rpm on 208-230/460 Vac power. NEMA 56 HC frames are available for motors with ratings of 1/2 through 1 HP, and NEMA 145TC frames are matched with 1 through 2 HP rated motors. Washdown motors resist water entry and drain condensation via their VBX INPRO/SEALÂ-® shaft seal, T drains, and nitrile conduit box...

Read More »
Transaxle features wound field motor.

Transaxle features wound field motor.

Model T523 DC Motor Transaxle incorporates cut steel helical gearing and splined interface between motor and transaxle. Axle shafts include oil seals that resist penetration of dirt. Transaxle features ball bearing construction, all aluminum housing, and neoprene mounting sleeves. Motors range from 12 through 48 Vdc and produce up to 2 hp. Gear ratios of 8.2:1, 11.1:1, 15.9:1, 23.2:1, and 29.4:1...

Read More »
AC Motor operates in severe environments.

AC Motor operates in severe environments.

Totally enclosed ac permanent split capacitor motor features clamshell housing, liquid-tight connectors, cast aluminum capacitor cover, heavy duty ball bearings, and steel shafts. Face-mount unit is available in power ratings of 1/4, 1/3, and 1/2 hp at 115 or 230 V in 50 or 60 cycle ac. Two-pole electrical design provides electrical current for both clockwise and counterclockwise directions at...

Read More »

All Topics