Reducer is corrosion-resistant for harsh applications.
Suited for washdown conditions of food/beverage industry, DODGEÃ-® E-Z KLEEN TIGEAR-2(TM) single-reduction right angle worm speed reducer employs 13-step coating system, stainless steel output shafts or hubs, and stainless steel hardware. Interior is protected by 2-piece harsh-duty sealing system. Unit delivers up to 6,800 lb-in. torque and is available in sizes 13-40 in Quill, Adaptable, and...
Read More »Compact Engine suits power generation applications.
Hitting 20 kVA power node, 404C-22G ElectropaK is offered in 50 and 60 Hz specifications with ratings of 1,500, 1,800, and 3,000 rev/min. Complying with all emissions legislation, it emits 2 Bosch Smoke Units and bare engine noise to 3 bB(A). Cooling pack, coupled with low air filter position, enable engine to provide optimum power density. Single canopy cross section fits entire range, and...
Read More »Laser Alignment System facilitates roll maintenance.
RollAlign(TM) visual laser tool facilitates field replacement of process rolls. Laser emitter unit, mounted on reference roll, projects two Class 2 fanned 635 nm laser lines onto reflector unit mounted on roll to be moved. This allows operator to view vertical angle (pitch) and horizontal angle (parallelity) as roll is adjusted into alignment. Product fits rolls of any diameter spaced between...
Read More »Engine meets all Tier 2/Stage II requirements.
Compact 404C-15 consists of 4-cylinder, 1.5 l engine developed to meet needs of light construction, agricultural, and lawn and garden equipment sectors. With max rating of 26.5 kW @ 3,000 rev/min, it can also be used for electric power generation and aircraft ground support. Engine provides low-noise performance and is scheduled for standard oil and filter changes every 500 hr.
Read More »Saving Energy with Efficient Belt Drives
By introducing energy efficient belts on electric motor drives, you can implement a simple, cost-effective solution to achieve energy savings in your facility.
Read More »External Linear Actuator is available in Size 11 model.
Size 11 hybrid actuator has rotating stainless steel acme lead screw incorporated into rotor and mating nut translating along screw. As motor steps, lead screw rotates but does not advance. Available in resolutions from 0.000125-0.002 in. per step, it delivers thrusts of up to 25 lb and has 4 in. of visible lead screw. Lead screw length, coil termination, and external nut can be customized to fit...
Read More »Brushless Servomotors deliver 574 oz-in peak torque.
Series TG2300, NEMA 23 Frame, DC Servomotors provide acceleration and deceleration of loads at up to 7,200 rpm. Electromotive coil technology uses multiple precision-machined copper sheets to replace magnet wire and iron core, eliminating magnetic saturation, eddy currents, and hysteresis. Model TG2300-120-81920E delivers peak current of 70 A and continuous power density of 7.5 W/oz. Motors...
Read More »Alignment Kit operates over distances of 80 ft.
Microgage Spindle and Shaft Alignment Kit consists of laser that is mounted to drive shaft, spindle, or gearbox flange, which projects precise reference beam along centerline. Digital target receiver catches laser beam and provides measurement reading to show if receiver is off-center. System measures misalignments as small as 0.0001 in. Angular errors can also be measured and eliminated. System...
Read More »Stepping Motor/Driver Packages have harmonic gearheads.
AlphaStep Series stepping motor and driver packages with built-in feedback devices are available with harmonic (HG) gearhead. Delivering zero-backlash performance, HG gearhead enables 1.65 in.Ã-² and 1.1 in.Ã-² motor models to produce max holding torque from 22-35 and 13-17 lb-in., respectively. AlphaStep Series uses microstep control and built-in feedback device that constantly monitors...
Read More »Right Angle Gear Motors run at 1,800 rpm.
Hollow Shaft Gear Motors can be base, end, side flange, shaft, or pilot mounted. Shaft options include Ã-¾ in. hollow, along with double and single extension Ã-¾, 5/8, and Ã-½ in. diameter shafts with keys. Three AC motor options and 4 DC motor options span horsepower range from 1/8 to Ã-¼ hp with gear ratios from 5:1-60:1. Gear motors are all ball bearing and synthetic oil...
Read More »Speed Reducers offer optional pressure equalization system.
Available as an option on all Series 700 speed reducers, PosiVent(TM) keeps water, washdown solution, and other airborne contaminants out of gearboxes in food processing and material handling applications. In aggressive production environments, PosiVent system replaces traditional vent plugs that can allow contaminants to enter gearbox during cool-down. Built with single seam, system can be...
Read More »Let Our Safety Experts Lower Your Risk
Elite Technical Services provides your company with qualified and experienced safety experts. Specializing in confined space and high-angle technical rescue and jobsite hazard assessment, your workplace safety is the top priority. Check out the video to learn more.
Read More »