Mechanical Power Transmission

Oriental Motor’s 1.8° PKP Series Stepper Motors are available in 42 mm and 56.4 mm frame sizes. Unit’s rotor comes with air gap of 30 µm. Motor uses neodymium magnet in the rotor design for reduced vibration. PKP Series motors are designed with increased bearing size and shaft for increased toque at low and high speeds.

Conta-Clip's New KDS-FP Flange Plate Offers IP66 Ingress Protection

Conta-Clip’s KDS-FP Flange Plate are available in KDS-FP-2x10/24 and KDS-FP-3 x 10/24 models with up to 20 or 30 configurable frame openings respectively. Consisting of 40 x 110 mm duct that is segmented into up to ten frame openings by snapping frame inlays, the inlays are offered in plain partitions, T-pieces or cross and double cross form.

Conta-Clip’s New KDS-FP Flange Plate Offers IP66 Ingress Protection

Conta-Clip’s KDS-FP Flange Plate are available in KDS-FP-2x10/24 and KDS-FP-3 x 10/24 models with up to 20 or 30 configurable frame openings respectively. Consisting of 40 x 110 mm duct that is segmented into up to ten frame openings by snapping frame inlays, the inlays are offered in plain partitions, T-pieces or cross and double cross form.

New GN 187.4 Stainless Steel Locking Plates are Compliant to RoHS standards.

GN 187.4 Stainless Steel Serrated Locking Plates are adaptable to range of applications. The units are made of different standard steel such as locking plates (American Standard Series 316L), guide housing (AISI 303) and conical thrust springs (AISI 301). The units enable interlocking of standards components at define angle.

Bearing Solutions For Recreational Applications

This white paper provides and overview of bearing solutions for recreational applications.

New GN 187.4 Stainless Steel Locking Plates are Compliant to RoHS standards.

GN 187.4 Stainless Steel Serrated Locking Plates are adaptable to range of applications. The units are made of different standard steel such as locking plates (American Standard Series 316L), guide housing (AISI 303) and conical thrust springs (AISI 301). The units enable interlocking of standards components at define angle.

New Radial Loc-N-Load™ Fixture Plate Uses CMM Palletization Features

Radial Loc-N-Load™ Aluminum Fixture Plate is available in 12, 18 or 30 in. rail and plate combinations with 8 in. diameter and 1/2 in. thick black hard anodized aluminum with 1/4-20 threaded holes. The plate comes with laser marked rings for simplifying process of aligning parts. Unit interlocks magnetically and can be installed on all CMMS. The fixture plate allows creation of multiple...

New Radial Loc-N-Load™ Fixture Plate Uses CMM Palletization Features

Radial Loc-N-Load™ Aluminum Fixture Plate is available in 12, 18 or 30 in. rail and plate combinations with 8 in. diameter and 1/2 in. thick black hard anodized aluminum with 1/4-20 threaded holes. The plate comes with laser marked rings for simplifying process of aligning parts. Unit interlocks magnetically and can be installed on all CMMS. The fixture plate allows creation of multiple...

Southco's New AC-EM 05 Electronic Actuator is Suitable for Limited Space Applications

Southco’s New AC-EM 05 Electronic Actuator is used for actuating mechanical latch to remotely open or unlock door when it is connected to electronic access control device. Unit offers enhanced gear motor operation and feature small profile design. The AC-EM 05 actuator is suitable for automotive, enclosures, bus, coach and RV applications and is offered with or without connector.

Southco's New AC-EM 05 Electronic Actuator is Suitable for Limited Space Applications

Southco’s New AC-EM 05 Electronic Actuator is used for actuating mechanical latch to remotely open or unlock door when it is connected to electronic access control device. Unit offers enhanced gear motor operation and feature small profile design. The AC-EM 05 actuator is suitable for automotive, enclosures, bus, coach and RV applications and is offered with or without connector.

New TBSM11 Linear Actuators Use StepSERVO™ Integrated Motor Technology

TBSM11 Linear Actuators come with RS-485 ports, ball screw shaft and nut assembly. The units deliver a thrust force of more than 20 lb with position resolution of 0.005 mm per full step. TBSM11 features motion control that can be programmed using Q Programming language. Units are suitable for electronics assembly, medical packaging, and test and measurement applications. Q Programming language...

Vector® Sports Training Ball Offers Visible Point of Contact

Our goal is to help every athlete derive maximum enjoyment from their sport and become a better player. We offer a line of innovative training tools that combine cutting-edge technology and out of the box thinking to deliver an unbeatable competitive advantage. The Vector® Sports Training Ball is just another example of our commitment to innovation. To learn how the Vector® is helping ballplayers everywhere, see our video.