Mechanical Components and Assemblies

Mounting Collars are stackable and adjustable.
Shaft Collars

Mounting Collars are stackable and adjustable.

Stackable Mounting Collars feature 2-piece construction with flats on 2 outside surfaces, which are drilled and tapped for attachment to each other, along with countersunk hole for mounting to any surface. Collars can accommodate wide range of hose, pipe and tube routing requirements. Available in bore sizes from 1/8 in. to 16 in. I.D., they can be made from steel, stainless steel and aluminum.

Read More »
Solder Covers protect CompactPCI boards.
Covers

Solder Covers protect CompactPCI boards.

SSC Solder Side Covers Series eliminate ESD and shorting problems associated with hot swappable 6U and 3U PCBs and peripherals. Covers protect solder side of PCBs with transparent puncture-resistant barrier. Made with ESD dissipative Mirrex 7002 certified PVC film, covers meet Bell Core GR-1421-CORE, EIA 541 and MIL-PRF-81705D specifications. Covers mount onto existing PCBs by using four small...

Read More »
Gas Springs for stock lifting and part ejection.
Gas Springs

Gas Springs for stock lifting and part ejection.

T2SS-16 Series gas springs provide complete force adjustability and seals that perform at all pressure ranges. Suitable replacements for 5/8 in. dia coil springs, they have shorter overall spring length for most stroke lengths, full rated force on contact so there is no need to preload, tightly toleranced overall height and more force with fewer springs.

Read More »
Precision Ground Insert has 3F geometry.
Inserts

Precision Ground Insert has 3F geometry.

Precision ground insert with 3F geometry for stainless steels, aluminum, high-temperature alloys and steels features periphery ground edges for accurate profiling and indexability. Additional features include light hones and positive geometry. Radii are available for light depths of cut and producing small corner radii. PVD grades offer layer of lubricity for reduced coefficient of friction....

Read More »
Cylinders are available with bore sizes from 3/4 to 8 in.
Hydraulic Cylinders

Cylinders are available with bore sizes from 3/4 to 8 in.

Q6 Hydro-Line Cylinders come with pressure-energized nitrile rod seals and nonmetallic piston wear rings. Pre-lubricated from factory, cylinders are suitable for non-lubricated air service up to 250 psi. Q6 NFPA-interchangeable cylinders feature precision-machined aluminum end caps and self-aligning, externally removable rod cartridge assemblies. Hydraulic HQ6 tolerates pressures to 400 psi, and...

Read More »
Bridge Handles feature counter bored mounting holes.
Handles, Pulls and Levers

Bridge Handles feature counter bored mounting holes.

Ergostyle® Bridge Handles are made from glass-fiber reinforced technopolymer plastic with black matte finish, while mounting holes are counter bored for socket cap screws and have technopolymer plastic cover caps available in variety of colors. Slight bend in handle distributes force on fingers during use. Resistant to solvents, oils, grease, and other chemical agents, handles are also...

Read More »
Couplings accommodate many bore sizes.
Shaft Couplings

Couplings accommodate many bore sizes.

Zero-Max CD® Couplings, with QD bushing hubs, are available in Single Flex and Double Flex models. Single Flex model provides misalignment up to 3° angular, 0.025 in. parallel and 0.160 in. axial. Double Flex model provides misalignment up to 3° angular, 0.089 in. parallel and 0.32 in. axial. Both are available with steel hubs to accept QD bushings in inch or metric bore sizes....

Read More »
Abrasive Wheels provide aggressive cutting.
Finishing Wheels

Abrasive Wheels provide aggressive cutting.

Cyclone Flap Wheels, made with aluminum oxide abrasive resin cloth, are available in stem-mounted and unmounted versions. Stem-mounted wheels are used in manual operations on portable tools and provide consistent aggressive action in hard-to-reach areas. Unmounted wheels are used on bench grinders and provide controlled grinding, finishing and deburring action on machined parts and flat surfaces....

Read More »

All Topics