Mechanical Components and Assemblies

Ball Transfer/Transfer Systems use hollow ball technology.

Ball Transfer/Transfer Systems use hollow ball technology.

Systems utilize hollow balls that provide 6,000 lb crush strength minimum per unit. Constructed with stainless cup and can for corrosion resistance, units have 1 in. stainless hollow ball riding on 1/8 in. stainless balls. Available with ball-up, ball-down, or angled mounting, products have nylon-flanged base and do not require lubrication. Operating temperature is 250°F, and load capacity is...

Read More »
Metric Air Cylinder suits panel lifting applications.

Metric Air Cylinder suits panel lifting applications.

Model HP.S offers dual port capabilities and uses square rod to prevent rotation. It features 50 mm bore size and is available in variety of stroke lengths. Adjustable cushioning on both ends allows cylinder to meet specific deceleration requirements. Maximum speed is 0.66 ft/sec and maximum working pressure is 140 psi.

Read More »
Damper Drive Module suits industrial applications.

Damper Drive Module suits industrial applications.

Module, compatible with all damper types, includes integral manual override and modulating or on/off control with failure mode options. Suitable for new installations or replacing existing electric/pneumatic drives, unit provides accurate air/gas flow control to burners, heaters, boilers, and turbine systems in power plants, refineries, and additional industrial applications.

Read More »
Products optimize wire performance in harsh environments.

Products optimize wire performance in harsh environments.

GB Xtreme(TM) wire terminals, lugs, primary wire, and cushion clamps withstand exposure to moisture, petrochemicals, acids, alkalis, UV rays, vibration, and salt water. Built from nylon, tin-plated copper, annealed stainless steel, and EPDM, products are suited for outdoor lighting, pool, irrigation, mower, pump, and likewise harsh environments. Terminals have nylon insulation that remains...

Read More »
Quick-Change Parallels fits company's 4 and 6 in. vises.

Quick-Change Parallels fits company's 4 and 6 in. vises.

Clak system aligns and locks into position on vise jaw plates, eliminating manual clamping and locking up of jaw components. Construction consists of 2 spring-loaded steel balls in base that snap into and lock corresponding jaw plate. Precision hardened and ground parallels slide and lock into place without need for hand tools. Offered in various heights, 6 pairs of parallels come as 1 set, boxed...

Read More »

Polymer Bearings provide snap-in installation.

Type 7 Nylon(TM) bearings provide double-flange construction that assures positive bearing retention for installation in thin plates. Available in metric and inch sizes, units offer .001 in. min diameter shaft-to-bearing clearance and compensation gap that allows bearings to be collapsed. Requiring no lubrication, corrosion-resistant products come in 7 sleeve, flanged, and snap-in types. Bearings...

Read More »
Jaw Couplings provide various dampening characteristics.

Jaw Couplings provide various dampening characteristics.

Fail safe Jawflex(TM) zero backlash jaw couplings are three-piece couplings comprised of two hubs and elastic element and come in two hardness levels. Polyurethane material on jaw provides dampening of impulse type loads and minimizes shock to motor and sensitive equipment. Couplings are available from .59-2.25 in. OD in both set screw style and NOMAR® clamp style and inch and metric bore sizes...

Read More »
Clamp Lever has soft-touch surface.

Clamp Lever has soft-touch surface.

AXL Clamp Lever has Pure Touch(TM) thermoplastic elastomer inlays, rounded edge design, and reinforced fiberglass body. Unit can be adjusted to 20-45 positions, with and without load. Pulling up on handle disengages unit to swivel into desired clamping position. Releasing re-engages clamp for tightening and loosening. Available in charcoal and black, product utilizes one TORX(TM) head adjustment...

Read More »
Rotary Shaft Seals handle extreme operating conditions.

Rotary Shaft Seals handle extreme operating conditions.

ROTAFLON(TM) seals handle high surface speed, high temperature, high pressure, and insufficient lubrication. Series MC has polymer seal lip with or without embedded spring energizer. Series RB offers polymer sealing surface bonded to elastomeric seal lip. Seals are chemical resistant and handle surface speed up to 5900 ft/min and temperature range of -58 to +500°F.

Read More »

All Topics