Mechanical Components and Assemblies

Inflatable Rubber Plugs are Inflated Using Compressed Air Lines

Inflatable Rubber Plugs are Inflated Using Compressed Air Lines

Inflatable Rubber Plugs are offered in sizes ranging from 2 – 78 in. Resistant to oils, hydrocarbons and petrochemicals, these plugs are made from the rubber comprising the mix of styrene, butadiene and isoprene. The plugs are used for blocking of pipes, joints, channels and inlets and are suitable for fluid production (milk, beer, chemicals), petrochemical, pharmaceutical, gas pipeline...

Read More »
Starke Series Polycarbonate Enclosures are Designed for Harsh Environments

Starke Series Polycarbonate Enclosures are Designed for Harsh Environments

Starke Series Polycarbonate Enclosures are offered in range of 72 sizes in opaque (ST) screw cover or clear (STCC) screw cover versions. Units are compliant with cULus, UL94-V2, Non-Halogenated, F1 rated and IEC 60529 IP66 standards. Enclosures raised bosses allow accommodation of back panel or DIN rail mounting for remote sensor mounting and small electronic controls.

Read More »
DVEO's Demodulator-Receiver and Decoder is Designed for Content Monitoring and Repurposing

DVEO's Demodulator-Receiver and Decoder is Designed for Content Monitoring and Repurposing

TLV500E-ATSC 3.0™ Demodulator-Receiver and Decoder comes with one BNC connector and supports 576i/480i, 576p/480p, 720p and 1080i/1080p resolutions. This unit converts HD input to SD out and provides 12G/12G/1.5G/1.5G or Quad 3G and HDMI 2.0 4K/60P outputs. The TLV500E-ATSC 3.0 comes with front panel controls, remote management software and upgradeable firmware. The unit features five slots...

Read More »
Hotrod® HHP Heating Cartridges are Used for Temperature up to 1,000

Hotrod® HHP Heating Cartridges are Used for Temperature up to 1,000

Hotrod® HHP Heating Cartridges are available in 12.5 mm, 16 mm and 20 mm diameters and are suitable for thermodynamic applications. These units come with housing casings made from the alloy Incoloy that is used in aerospace applications. The Icoloy is formed by the controlled composition of carbon, aluminum, titanium, silicon and manganese.

Read More »
JW Winco's Gear Lever Handles are RoHS compliant.

JW Winco's Gear Lever Handles are RoHS compliant.

JW Winco’s Gear Lever Handles are offered in steel and stainless steel versions in inch and metric sizes. These steel levers come with blue passivated finishing and various operating knobs whereas the stainless steel levers feature sandblasted satin finish. Lever’s knobs are made of black Duroplastic and are resistant to heat of up to 150°C.

Read More »
ArmorPad™ Equipment Mounting Pad features a lightweight and dense foam core bottom.

ArmorPad™ Equipment Mounting Pad features a lightweight and dense foam core bottom.

ArmorPad™ Equipment Mounting Pad is available in 61, 76, 81, 91, 101-cm² x 7.6 cm high. Unit is made from dense foam core base and is covered in shell of durable polymer. This pad is suitable for residential and commercial air conditioning condensers. Unit’s polymer surface is resistant to UV degradation, coil cleaning chemicals, landscaping chemicals and weather. Product can hold drilled-in...

Read More »
Polymer Bearings and Aluminum Shafts are designed for power transmission line.

Polymer Bearings and Aluminum Shafts are designed for power transmission line.

AutomationDirect offers three styles of igus DryLin R series linear plain bearings, igubal series mounted spherical bearings and iglide series plain bearings and DryLin R series hard-anodized shafts. These anodized-shafts are available in four diameters and three lengths up to 1 m. Plain bearings are made of J (low friction), G300 and T500 materials whereas. Spherical bearings are manufactured...

Read More »
TECHSPEC's Assemblies facilitate magnification using extension tubes.

TECHSPEC's Assemblies facilitate magnification using extension tubes.

Helping achieve similar imaging performance of infinity corrected objectives, TECHSPEC® Ultra Compact Objective Assemblies are designed at 2X magnification and can be configured to achieve 4X, 5X, 10X, 15X, and 20X magnifications by adding longer extension tubes. RoHS compliant, assemblies are available in four models with 2X magnification, with focal lengths of 8mm or 10mm. Unit features five...

Read More »
Stafford's Bore Shaft Components are designed for military vehicle applications.

Stafford's Bore Shaft Components are designed for military vehicle applications.

Stafford’s Bore Shaft Components include shaft collars, rigid couplings and flange mounts. These shaft collars are available in sizes up to 14 in. I.D. and varying O.D.’s, rigid couplings with bores to 6 in. and lengths to 16 in. and flange mounts with bore sizes 6 in. These components are made from steel, stainless steel, special alloys and aluminum and are suitable for fire-fighting...

Read More »

All Topics