Mechanical Components and Assemblies

Packing seals without adhesives or expansion.
Gaskets

Packing seals without adhesives or expansion.

Pre-Energized Vee Packing design model features geometry that guarantees tight seal. It does not require tightening of packing gland against seal or use adhesives at installation. It also does not rely on packing material swelling, which means product is suitable for use in water hydraulics and bio-degradable fluids. Available in sizes from Â-¼-96 in. dia in 20+ material configurations,...

Read More »
Photochemically-Etched Parts target cell phone industry.
Partition / Privacy Screens

Photochemically-Etched Parts target cell phone industry.

Custom photochemically-etched metal components such as gaskets, EMI/RF shields, face plates, and screens are available in thicknesses from thin foil up to 0.090 in. Intricate patterns, geometries, and graphics can be incorporated into part, and all types of surface finishes can be applied. Components are suited for wireless and portable handheld cell phones as well as other communications and...

Read More »
Equipment Boots

Sealing Boots protect industrial and miniature switches.

Available in variety of colors, Sealing Boots prevent entry of dust, sand, water, and other contaminants. They can be screwed onto switch bushing or snapped over switch actuator, depending on switch type and panel mounting mode. Rated IP67, each boot is supplied with sealing ring or washer and allows for full immersion under 1 m of water for 30 min without water ingress. Applications include...

Read More »
Expansion Joints feature limit cables instead of limit bolts.
Expansion Joints

Expansion Joints feature limit cables instead of limit bolts.

Offered in diameters from 1-12 in. with 2, 3, and 5 convolutes, Cable Style Expansion Joints compensate for axial, lateral, and angular movements between 2 anchored points in pipeline. Limit cables facilitate installation between fixed flanges and joint, and can be compressed and bolted in place without interference from integral limit bolts. Joints feature Type 316 stainless steel reinforcing...

Read More »
Toroidal Roller Bearings suit industrial fan applications.
Bearings

Toroidal Roller Bearings suit industrial fan applications.

CARB® bearings perform as non-locating bearings in self-aligning bearing systems for industrial fans. Compact, radial roller bearings compensate internally for angular misalignment and accommodate axial shaft expansion. Raceway profiles result in minimized frictional running and reduced operating temperatures. Used with same standard housings and accessories as other self-aligning bearings,...

Read More »
Clamping Module features holding forces to 75,000 N.
Power Clamps

Clamping Module features holding forces to 75,000 N.

Measuring 196 mm in dia, NSE 196 module is mechanically clamped and pneumatically opened, allowing clamped system to be moved in clamped state without interference from air lines. Clamping pin has a 61 mm dia through hole, which makes it possible for workpiece to protrude through clamping system. To facilitate orientation of fixture plates, module also comes with 12 mm precision bore on face.

Read More »
Vibration and Mechanical Dampers

Vibration Dampening System is designed for mezzanines.

Intended for applications where sound and vibration are detrimental to process operation, noise and vibration dampening system employs mezzanine deck comprised of alternating isolated layers of solid, soft, and acoustical materials. Fastening system eliminates transfer of vibration and sound between layers, while isolation barrier is utilized between beams and columns and between columns and...

Read More »
Drive Pins reduce slippage in hard turning applications.
Pins

Drive Pins reduce slippage in hard turning applications.

Micro-serrated, hard-coated Neidlein face driver drive pins reduce or eliminate part slippage, reduce scrapped parts, and increase turning productivity. If part slips, it will not remove serrations or coating, and pins can be used again. Products achieve circular run outs of less than 0.0007 in. in long production runs. Drive pins can be used with SB/FSB and FFB face drivers and all special...

Read More »
Clamping Devices offer hydraulic and pneumatic operation.
Power Clamps

Clamping Devices offer hydraulic and pneumatic operation.

Stronghold(TM) Select products work together as part of complete workholding system. Available in 18 styles, hydraulic swing/pull clamps come in 475, 1,100, and 2,400 lb sizes. Hydraulic work supports include 1,650, 2,500, 5,000, 7,500, and 10,000 lb models, all in spring advance style. Treated metal surfaces offer corrosion resistance, while seal and wiper technology resists contamination and...

Read More »
Elastomer Cushions mount externally to pneumatic cylinders.
Shock Absorbers

Elastomer Cushions mount externally to pneumatic cylinders.

Offering alternative for pneumatic cushions, NuCushions provide quiet operation without adjustment, and eliminate need for bleed needle assembly, cushion spud, and spud seal. Units compensate for velocity, weight, and pressure, and are unaffected by oil, grease, chemicals, sunlight, salt spray, and hydraulic fluids. Cycle rates are maintained without loss of cycle time.

Read More »
Tekna Manufacturing LLC Announces NFPA 99 Compliant Model 7200 Multiplace Chamber
Sponsored

Tekna Manufacturing LLC Announces NFPA 99 Compliant Model 7200 Multiplace Chamber

Tekna is a leader in Monoplace and Multiplace Hyperbaric Chambers for Hyperbaric Oxygen Therapy (HBOT), offering products that set the standard for quality and innovation. Our new 7200 series of multiplace chambers is a state-of-the-art system that integrates advanced engineering with a plethora of features and options making it the industry's premier HBOT system. To learn more, see our video.

Read More »

All Topics