Standard Motor Products Releases 220 New Parts for TechSmart®
NEW YORK- – Standard Motor Products, Inc. (SMP) announces the addition of 220 new part numbers to its TechSmart-® line. The release increases new coverage through 2015 for an additional 118 million VIO. TechSmart-® continued to expand its electronic throttle body category by adding 50 new parts. In total, TechSmart's line now features more than 130 direct-replacement units covering more than...
Read More »Narrowband Receiver enhances healthcare patient monitoring.
NXP SA606 RF-IF ICs can connect- cardiac patient's implanted device to clinic or doctor's office via- standard phone line or cellular phone. Monolithic FM IF system incorporates mixer/oscillator,- 2 limiting intermediate frequency amplifier blocks, quadrature detector, logarithmic Received Signal Strength Indicator (RSSI), voltage regulator, and audio and RSSI op amps. Remote monitoring...
Read More »Hydraulic Sealing Bearing suits heavy-duty equipment.
For optimized alignment and to minimize risk for metal-to-metal contact between moving parts, Hallite 708 is fully machined to tight tolerances on thickness. Fit-for-purpose solution is suited for heavy-duty cylinder uses, such as mining roof supports and forestry equipment. Available in inch and metric sizes, bearing is most advantageous- in- applications that require high load bearing,...
Read More »
Process Piping: Everything You Need & Should Know
Learn how process piping differs from other systems, key considerations, and how it's applied in different systems.
Read More »
FireflySci Presents New Test Plate Line for Instrument Validation of Microplate Readers
BROOKLYN, N.Y. - Any quality assurance, metrology or quality control person knows all too well, the stress that an ISO audit can bring about. Hearing about an upcoming ISO-17025 audit is enough to make one break into a cold sweat. A section 5.6 nonconformance, i.e. using a non-approved or un-accredited calibration provider is one of the more common nonconformances and can cause expensive setbacks...
Read More »Plymovent Installs More than 30 Hose Reels
Cranbury, NJ – The Equipment Maintenance Operations Center (EMOC) in Montgomery County, Maryland maintains more than 150 transit buses and 500 maintenance vehicles for both the county Department of Transportation and the Department of General Services. When the new fleet maintenance facility was designed special attention was given to ensure it will be environmentally friendly and a healthy...
Read More »Two-Part Clamps support coarse- and fine-profile conduit.
Featuring- single rib that makes brackets compatible with both coarse- and fine-profile conduit, PMA-® GP Two-Part Support Clamps are designed for use in rail vehicles and vehicles with particularly demanding requirements, as well as wind turbines and other special-purpose machinery. Units offer simplified assembly, with locating pins to lightly hold 2 halves in position. By allowing conduit to...
Read More »
Macron Dynamics Introduces New T-Bot and H-Bot Gantry Systems to Linear Robotics Line
t-bot 12 model Macron's new T-Bot model TBG-12 CROYDON, Pa – Macron Dynamics, Inc., a manufacturer of linear robotics motion systems and automation components, recently introduced two new products to their T-Bot and H-Bot gantry robot product lines, the TBG-12 and the HBG-12. The new products are smaller, lighter, and designed to complete difficult jobs both efficiently and accurately. There...
Read More »
FIPA Combines Experience, Quality, & Creativity to Increase Efficiency, Production, & Profit in the Woodworking Industry
FIPA recently designed delivered a complete, custom, cost-effective material handling solution that allows a single employee to safely & easily lift, relocate, & precisely place large, rough-hewn planks weighing up to 353lbs (160kg) CARY, N.C. — FIPA Inc., a leading manufacturer of advanced vacuum technology, gripper systems, air nippers, tube lifters, and End-of-Arm-Tooling (EOAT), recently...
Read More »New Improved Package for P-80 1 Pint Containers
Burlington, New Jersey, USA –- International Products Corporation (IPC) is pleased to announce the debut of a new metric container and updated package design for the pint size of P-80-® Emulsion temporary rubber assembly lubricant. A new 475 mL bottle will replace the 1 pint container; it will be available in cases of 6 and 12. For those wishing to utilize a sprayer with the new bottle, a...
Read More »
Ensure Safety, Reliability in Your Cement Plant with Aerzen Blowers and Compressors
Aerzen offers blowers and compressors for challenging cement applications such as pneumatic conveying from raw mill to raw meal silos, combustion air, cement silos fluidization, and more. At Aerzen, safety is our top priority. Check out our video to learn more.
Read More »
