Material Processing

Protective Sleeves save labor.
Sleeves

Protective Sleeves save labor.

Coated, ballistic Cordura(R) Sidewinder sleeves, with industrial hook and loop closure, allow easy assembly and removal. Sleeves install without disconnecting hydraulic, electrical, and pneumatic hose and cable bundling and can be removed easily for hose maintenance. Material is available in variety of circumferences and bulk lengths to 150 ft for OEM and maintenance operations.

Read More »
Air Dryer offers alternative to refrigerant technology.
Desiccant and Membrane Dryers

Air Dryer offers alternative to refrigerant technology.

Balston Membrane Air Dryer will dry compressed air to dewpoints as low as -40°F at flow rates up to 100 SCFM. It has no moving parts and operates without attention. Coalescing prefiltration is employed immediately upstream of membranes to protect them from pipe scale, particulate, and liquids. Dryer requires no electrical connections, which makes it ideal for remote and point-of-use...

Read More »
Desiccant Air Dryer works without heat.
Desiccant and Membrane Dryers

Desiccant Air Dryer works without heat.

Optima LX Series heatless desiccant compressed air dryer provides ultra dry air required for critical compressed air applications. It has maintenance free shuttle valves, high efficiency coalescing prefilter, and particulate removal afterfilter. Non-lubricated switching valve and two solenoid-operated purge valves replaces up to 13 separate valves used in company's other designs. Dryers are...

Read More »
Belt-Driven Boom positions robots and gantries.
Work and Load Positioners

Belt-Driven Boom positions robots and gantries.

DGEA toothed-belt-driven electric boom-arm axis is suitable for positioning applications requiring horizontal or vertical projecting motions. Fixed pinion drive mechanism engages stationary toothed belt, causing projecting structure to traverse work envelope. Roller guide bearing system is integrated into housing. Unit has stroke range of 100-1,000 mm, payload of 110 lb, speed of 2.1 m/sec, and...

Read More »
Shot Blaster is suitable for concrete, steel, and stone.
Abrasive Blast Equipment

Shot Blaster is suitable for concrete, steel, and stone.

Blastrac® 1-5HH hand-held shot blaster can be used for decorative concrete applications such as stenciling and more. Virtually dust-free, 1-5HH cleans and prepares small floor and wall surfaces, balconies and stairways, and small metal surfaces such as weld seams. Applications of this 110V unit include cleaning, contouring, and preparation for repair and restoration work. 1-5HH may be used...

Read More »
Curing Systems

UV Curing System operates in power class of 500 watts/in.

Six inch Light Hammer 6 consists of 2 modular components: microwave-irradiator and solid-state power supply. Electrode-less bulb, mounted in elliptical reflector, focuses intense strip of light 2.1 in. below surface of lamp. System repeatedly cycles from high power to very low power over a few seconds. Power output from 25 to 100 percent is controlled from front panel or remotely through analog...

Read More »
Curing Systems

UV Curing System can be used individually or in groups.

PowerCure(TM) 3, three in., microwave-powered lamp system operates in 250 watts/in. power class. It can be used in focused (10mm) or out-of focused distances, fits into X-Y tables, and requires minimal amounts of air for positive pressure cooling. PowerCure 3 is available with D-bulb, and achieves rapid startup using technology that does not require separate igniter bulb. Full cure width and...

Read More »
Filter Driers clean refrigerant in one pass.
Dryers

Filter Driers clean refrigerant in one pass.

Dual in-line One-Pass Filter Driers provide 35 column in. of desiccant that is able to clean and dehydrate refrigerant on single pass to very near ARI-700 specifications. Installing filter on inlet side of purge tank helps protect purge tank from corrosion and acid build-up, helps prevent corrosion build-up on purge tank heat transfer coils, and helps remove acid and moisture from chiller's...

Read More »
Tilt Trays are made of ABS plastic.
Trays

Tilt Trays are made of ABS plastic.

Replacement Tilt Trays for sorters are thermoformed from 3/8 in. thick ABS plastic, and feature chemically-bonded back lip for additional strength. Weighing 9.2 lbs each, virtually unbreakable tilt trays are available to fit sorters manufactured by Alvey, Buschman, Crissplant, Dematic, HK Systems, Kosan, and Matthews. Trays are drilled to OEM specifications for direct replacement.

Read More »
Machine combines shearing, press-braking, and rolling.
Shears

Machine combines shearing, press-braking, and rolling.

TRI-FAB Model 52P features shearing and rolling capacity of 52 in. x 12 ga mild steel and press braking capacities of 12 ga at 36 in. and 14 ga at 52 in. Machine will cut stainless steel up to 0.072 in. Rotating shafts are journalled in bronze bearings, and shear blades are Grade T10 tool steel. Manually-operated back gauge is standard, and can be positioned for use with shear or press brake as...

Read More »
Oilfield Improvements® Wheeled Rod Guide® Couplings Celebrate 35th Anniversary
Sponsored

Oilfield Improvements® Wheeled Rod Guide® Couplings Celebrate 35th Anniversary

For over 35 years our Wheeled Rod Guide Couplings, have been at work in oil fields across the globe. Our products are engineered to extend the service life of sucker rods and tubing, delivering cutting-edge innovation that enhances oilfield operation, maximizes output, and enhancing overall operations. To learn about the advantages of using Wheeled Rod Guide Couplings in your wells, see our video.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers