Machinery & Machining Tools

Indexable Milling Cutters optimize steel and cast iron machining.
Cutting Tool Inserts

Indexable Milling Cutters optimize steel and cast iron machining.

Providing wear and shock resistance, CVD-Al2O3-coated Tiger-tecÂ-® Silver WKP25S maximizes productivity through ability to process all steels at high cutting speeds. Product features bicolor coating that facilitates wear detection. Grade is also suitable for machining tool steels with strengths greater than 1,000 N/mm² and when used in difficult conditions such as wet machining. In...

Read More »
HASCO - Innovations at FAKUMA in Friedrichshafen
Controls and Controllers

HASCO - Innovations at FAKUMA in Friedrichshafen

HASCO's Mould Base and Hot Runner divisions will present a variety of innovative solutions for mouldmaking and tooling design at the upcoming FAKUMA in Friedrichshafen. The Lüdenscheid/Germany-based company is specialised in the development and manufacture of standard mould units and hot runner systems for the plastics processing industry. The Mould Base Division will introduce its newly...

Read More »
AIDA Introduces New MCX Straightside Presses
Presses

AIDA Introduces New MCX Straightside Presses

AIDA-America Corp., Dayton, OH, introduces its new line of straightside stamping presses, the MCX Series. The MCX, modular configuration series presses, offer stampers a wide array of press configurations and specifications. Options include: single or double gear, -¼ or ½ inch rating points, five drive options, including mechanical or servo, a wide variety of stroke lengths and die height...

Read More »
HASCO - Innovations at FAKUMA in Friedrichshafen
Controls and Controllers

HASCO - Innovations at FAKUMA in Friedrichshafen

HASCO's Mould Base and Hot Runner divisions will present a variety of innovative solutions for mouldmaking and tooling design at the upcoming FAKUMA in Friedrichshafen. The LÃ-¼denscheid/Germany-based company is specialised in the development and manufacture of standard mould units and hot runner systems for the plastics processing industry. The Mould Base Division will introduce its newly...

Read More »
A Guide to Quality Control of the SMT Process
Sponsored

A Guide to Quality Control of the SMT Process

The printed circuit board (PCB) manufacturing process begins with cutting-edge equipment capable of accurately picking and placing up to 40,000 components per hour. This innovative equipment keeps error rates extremely low, and those defects that do occur are quickly caught by sensitive laser and optical inspection equipment.

Read More »
AIDA Introduces New MCX Straightside Presses
Presses

AIDA Introduces New MCX Straightside Presses

AIDA-America Corp., Dayton, OH, introduces its new line of straightside stamping presses, the MCX Series. The MCX, modular configuration series presses, offer stampers a wide array of press configurations and specifications. Options include: single or double gear, Â-¼ or ½ inch rating points, five drive options, including mechanical or servo, a wide variety of stroke lengths and die...

Read More »
Sensors / Detectors / Transducers

Wafer Defect Review System is designed for 20 nm node.

Suitable for chip manufacturing at 20 nm device nodes and below, eDR(TM)-7000 electron-beam (e-beam) wafer defect review system addresses defect imaging and classification challenges at leading edge or located at bottom of deep trench/hole. System can drive directly to site of defect at high resolution, enabling review of multiple defects per second. Features include stage and vibration-isolation...

Read More »
Laser Alignment Tuning Kits support research setups.
Aligners

Laser Alignment Tuning Kits support research setups.

Equipped with 1917-R laser power meter, LAKIT Series Tuning Kits utilize broad selection of optical detectors, including silicon, Germanium, or thermopile detectors. Units operate in wavelengths from 200 nm to 10.6 microns, with up to 100 W average power. Series 918D, designed for low power lasers less than 2 W/cm-², operates in visible or IR spectrum. Series 818P thermopile detectors are suited...

Read More »
Sensors / Detectors / Transducers

Wafer Defect Review System is designed for 20 nm node.

Suitable for chip manufacturing at 20 nm device nodes and below, eDR(TM)-7000 electron-beam (e-beam) wafer defect review system addresses defect imaging and classification challenges at leading edge or located at bottom of deep trench/hole. System can drive directly to site of defect at high resolution, enabling review of multiple defects per second. Features include stage and vibration-isolation...

Read More »
Laser Alignment Tuning Kits support research setups.
Aligners

Laser Alignment Tuning Kits support research setups.

Equipped with 1917-R laser power meter, LAKIT Series Tuning Kits utilize broad selection of optical detectors, including silicon, Germanium, or thermopile detectors. Units operate in wavelengths from 200 nm to 10.6 microns, with up to 100 W average power. Series 918D, designed for low power lasers less than 2 W/cmÂ-², operates in visible or IR spectrum. Series 818P thermopile detectors are...

Read More »
Rehm Prepares to Launch New Locally-built Convection Soldering System at Nepcon Shenzhen, Stand 1H38
Soldering Machinery

Rehm Prepares to Launch New Locally-built Convection Soldering System at Nepcon Shenzhen, Stand 1H38

Rehm Thermal Systems has confirmed plans to releases its highly anticipated VisionXC convection soldering system on stand 1H38 at this year's Nepcon Shenzhen exhibition. Taking place on August 30th in China's Shenzhen International Convention & Exhibition Center, the event will see Rehm unveil its brand new system, exclusively manufacturer in, and developed for, the Chinese marketplace. Extending...

Read More »

All Topics