Machinery & Machining Tools

Machinery & Machining Tools

Tap Extensions replace extra-length taps.

Nov 21, 2001

Style B Tap Extensions can be used for machine and hand tapping. Each extension fits individual tap sizes, and square or round sockets conform to size standards of most tap manufacturers. Close-fitting deep socket of extension supports tap, which is held firmly in place by 2 socket set screws bearing 90° apart on square of tap. Extensions are available individually or in sets that fit 15 tap... Read More

Machinery & Machining Tools

Grinding Fixture helps resharpen tools.

Nov 21, 2001

R-O Form relief grinding fixture provides ability to resharpen steel and carbide multiple step drills, reamers, core drills, taps, countersinks, counter bores and gun drills. It provides constant radial arc of form relief, so heat will travel to trailing edge of flute and disperse in chips. Fixture can be used for both axial and radial relief. It works with collets or between centers. Cams are... Read More

Machinery & Machining Tools

Plasma Arc Cutter requires little maintenance.

Nov 19, 2001

Portable PowerCut 1500 plasma arc cutting machine has automatic pilot arc start, trigger lock and 40 A nozzle for drag cutting. Torch combines swirl baffle with tip, so there are fewer parts to replace and no alignment errors from installing parts incorrectly. It works on auxiliary power from most welding engine drives and tolerates poor power lines. It arrives fully assembled with torch parts in... Read More

Machinery & Machining Tools

Wire Stripper Prefeed speeds up stripping process.

Nov 19, 2001

Belt-driven Model 6815-05/06 improves wire strip-length accuracy and extends life of wire strippers by reducing load pressures, thus preventing jamming and excessive strain on equipment and materials. It delivers any length wire to any make of wire processing machine, provides power to rotate maximum weight reels or pull wire from a barrel, and has provision for mounting 2 reels for cutting and... Read More

Machinery & Machining Tools

Grinder is available with 3 to 5 hp motors.

Nov 17, 2001

Annihilator(TM) solids reduction unit features counter-rotating, hexagonal shaft coupled with 5-tooth, hardened steel cutters to process from 300 to 4,250 gpm of influent. Grinder can prolong service life of downstream equipment such as pumps, sensors, monitors and valves. Seal/bearing cartridge assembly eliminates need to disassemble entire grinder when servicing. Electronic control panel offers... Read More

Machinery & Machining Tools

Gripping Rails with Clamps improve holding force.

Nov 16, 2001

Pitbull Gripping Rails, with built-in clamps, maintain parallelism on non-ferrous or ferrous parts. Their asymmetric design allows for precision tolerances. Pitbull Gripping Rails also improve holding force of magnetic chucks when used to hold difficult or irregularly shaped ferrous workpieces. They allow users to add extra steel blocking to increase resistance against sliding, and can hold large... Read More

Machinery & Machining Tools

Test and Taping System conserves factory floor space.

Nov 16, 2001

MP-PLUNGE test and tape machine is designed for mid-volume input from tube or bulk-to-tape applications requiring plunge-to-board test capability. It achieves throughputs of up to 3,600 pph and its integrated processes include vision inspection, electrical test and taping with optional laser mark capabilities. Unit is RF-compatible and interfaces with most standard testers. Rejected parts are... Read More

Machinery & Machining Tools

Interchangeable Tooling fits most punch presses.

Nov 15, 2001

Ultra XT tooling line combines quick setup, easy installation, fast maintenance and interchangeability with other suppliers' tools and tooling systems. Tooling has hardened and ground guides, which reduce abrasive action of punching, and interior and exterior spiral grease grooves, which diffuse heat. Unit works with Amada, Finn-Power, Murata Wiedemann, Euromac, Nisshinbo, Strippit and other... Read More

Machinery & Machining Tools

Welding End Prep Tool removes tube stubs from header.

Nov 15, 2001

Mini MILLHOG® air-powered ID clamping end prep tool produces high torque at low rpm for milling hardened welds that have been exposed to high heat and pressure cycling. Its heavy-duty mandrel features clamp ribs that will not flex. Running at 34 rpm and generating 1,200 ft-lb of torque at cutter blade, Mini MILLHOG uses TiN-coated blades to produce a clean, continuous chip without cutting... Read More

Machinery & Machining Tools

Plasma Cutting Package weighs only 35 lb, goes anywhere.

Nov 15, 2001

Lightweight and portable, Handy Plasma 550 has 35 A of cutting power at 40% duty cycle, making it able to cut 1/2 in. material. Output is adjustable so operator can tailor current for material to be cut. Power line conditioner lets unit operate off auxiliary power sources and handle poor power lines without damage, making it suitable for field use. It comes with company's PT-31 torch for drag or... Read More

Machinery & Machining Tools

Straight Side Press forms and blanks.

Nov 15, 2001

General-purpose press has operating range of 220 to 1100 tons, runs at 150 strokes/min, and has stroke range from 3.9 to 24 in. Press is available in 3 configurations: eccentric motion/single gear reduction for constant slide velocity; eccentric motion/double gear reduction that increases torque for heavier loads; and link motion/double gear reduction unit that offers 50% more torque while... Read More

Machinery & Machining Tools

Laser Cutting System handles 5 x 10 ft sheets in 3 dimensions.

Nov 14, 2001

6-axis Domino 1530 machine tool provides 2 and 3-dimensional cuts with CO2 lasers rated 2,500 W to 4,000 W. It works in X and Y horizontal axes and Z vertical axis, and rotates horizontally and vertically. Its sixth F-axis allows programming of laser's focal length to automatically adapt to range of ferrous and non-ferrous materials of different thickness. Operator no longer needs to make manual... Read More

Machinery & Machining Tools

Miter Saw Stand holds boards up to 16 ft long.

Nov 13, 2001

DW723 miter saw stand weighs 35 lbs, has folding legs that lock in place for stability, and supports loads up to 400 lbs. Adjustable extension arms slide out horizontally from both ends of unit, providing platform for cutting. Stand comes with two flip stop/supports that aid in consistent, accurate cutting. Length (folded) is 5-1/2 ft, width (folded) is 10 1/4 in., and height is 7-1/2 in.... Read More

Machinery & Machining Tools

Debur Cell automates deburring and chamfering.

Nov 09, 2001

S 450/750 DBC Gear Debur Cell eliminates need to manually debur and chamfer gears through use of FANUC 6-axis servo-driven robot and programmable controller. Cell can be programmed to perform both top and bottom tooth and root gear deburring and chamfering geometry. Model S 450/750 DBC is available in two sizes: 2 in. through-hole with 18 in. dia, and 4 in. through-hole with 30 in. dia. Read More

Machinery & Machining Tools

Flap Disc combines two abrasive grains.

Nov 09, 2001

TwinFiber(TM) Type 29 flap disc combines ceramic seeded-gel and zirconia alumina abrasives for use on stainless and carbon steels. Blending of 2 abrasives onto Y-weight cotton backing produces disc that works with less pressure. Type 29 angled face and conical shape allows operators to grind at 10° angle. TwinFiber disc is available in 4-1/2 in. and 7 in. diameters with quick mount hubs. Read More

Machinery & Machining Tools

Cutting Machine features monolithic column design.

Nov 09, 2001

PHOENIX® II 275 HC CNC Bevel Gear Cutting Machine is designed to machine gears with pitch diameters up to 275 mm. While it can accommodate wet cutting processes, it is well-suited for dry machining. Cutter spindle and work spindle are mounted directly to column, and cutter spindle pivots to create root angle, rather than mounting workspindle on rotating base. Machine includes direct-drive... Read More

Machinery & Machining Tools

Wet Blasting Machine uses water as an abrasive.

Nov 08, 2001

Suitable for automotive parts, the Fuji Seiki wet blasting machine can be used for deburring, matte finishing, scale removal, peening, surface treatment, edge-breaking and cleaning. Applicable workpieces include engine parts, turbo fans, clutch parts, fuel injection nozzles, ABS parts, intricate workpieces, and more. Standard sizes range from 48 x 78 x 86 in. to 80 x 100 x 96 in. Maximum... Read More

Machinery & Machining Tools

Autofeed Screw System suits drywall applications.

Nov 08, 2001

Fastening Model SS2K features solid steel components, patented fastening system and Milwaukee 4000 rpm drive. It accommodates various drive screws from 1 in. to 2 in. and in #6, #7 and #8 diameters. Applications include drywall installation and metal framing in light construction. Bit changing is accomplished via tool-free processes. Read More

Machinery & Machining Tools

Machine installs internal O-rings and seals,.

Nov 08, 2001

Internal O-Ring and Seal Installation Machine installs O-rings or seals into internal grooves with semi-automatic operation. Operator places part into holding fixture and actuates machine. O-ring or seal is automatically installed into internal grooves. Machine achieves rates of up to 30 parts per minute, and can be tooled to accommodate different sized O-rings and seals. It can also be... Read More

Machinery & Machining Tools, Welding Equipment & Supplies

Straightener/Feeder features computer control.

Nov 08, 2001

LCC-HF2 Straightener/Feeder, equipped with HM-type Computer Control System (CCS), handles metals from 1.97 in. to 39.37 in. wide and up to 0.18 in. thick. It accepts maximum coil weights up to 10 tons and maximum coil O.D.s of 60 in. Features include no-loop detector, photo sensor loop control, pilot roll, handwheel adjustment, end-of-stock detector, and pneumatic or hydraulic expansion systems. Read More