Lubricants

Cleaning Products & Equipment, Lubricants

IPC Introduces New and Improved Package and Label Design!

Dec 14, 2010

New and Improved Packaging from International Products Corporation Burlington, New Jersey, USA: International Products Corporation is pleased to announce the introduction of new packaging. In addition to the new design, the bottles will be available in standardized metric sizes worldwide. "It's been years since we've had a major packaging revision," says President, Kathy Wyrofsky. "We think the... Read More

Green & Clean, Lubricants

Dry Film Lubricant serves as assembly aid.

Dec 08, 2010

Consisting of 15% aqueous dispersion of PTFE, NyeFilm® 501F is applied in wet form, which then dries to surface. Product was developed to have controlled particle size distribution where no particles are greater than 10 microns, allowing for even distribution of PTFE. Environmentally safe, NyeFilm® 501F offers rub and abrasion resistance as well as chemical compatibility with all polymers. Read More

Lubricants

Nye Exhibited at SemiconWest 2010, in San Francisco, CA

Dec 08, 2010

Nye Lubricants introduced new products from its NyeTorr® and NyeClean® product lines at SemiconWest 2010. The show took place in the Moscone Center in San Francisco from July 13 to July 15. It was the second year in a row that Nye Technical Team exhibits there. This year, we introduced new ultra low outgassing products. Those products have been carefully engineered through the past year,... Read More

Lubricants

New Product: NyeFilm® 530, Fishing Reel Lubrication

Dec 08, 2010

A 5% dispersion of ester wax in an isoparaffinic solvent. This lubricant provides friction reduction, wear protection and corrosion resistance for salt water conditions.

Lubricant Properties Typical Value Test Method Recommended Service Range (°C) -30 to 250 Color, Appearance Amber Base Oil Kinematic Viscosity 25°C ASTM D-445 Flash Point °C 290 ASTM D-92 Boiling Point 156°C ASTM... Read More

Lubricants

Polyurea Grease prolongs electric motor life.

Nov 10, 2010

Designed to help electric motor bearings run cooler and last longer, Monolec® Extend EM Grease (1282) increases motor efficiency by decreasing drag. It offers mechanical stability even in high-moisture environments and contains Monolec proprietary wear-reducing additive. Resistant to oxidation, NLGI grade 2 grease protects bearings against rust and corrosion and also resists water spray-off.... Read More

Green & Clean, Lubricants

High-Temperature Lubricant uses organic and inorganic content.

Oct 27, 2010

Able to be used in temperatures from ambient to 1,000°C, Keralon-B is brushable lubricant/coating/paint based on organic Methylated Seed Oil and inorganic ceramic mixture of chemically-inert lubricating phases: Boron Nitride, Graphite, and Titanium Dioxide. It performs as oily mixture at room temperature and acts as dry film lubricant above 200°C. Solution is nonreactive/nonwetting with... Read More

Lubricants, Machinery & Machining Tools

An Upgrade in QUAKERAL® Coolant Technology Sums up to Increased Savings

Sep 20, 2010

Demonstrating a proactive approach to continuous improvement, a joint effort was undertaken by Quaker Chemical (NYSE: KWR) and an automotive customer to upgrade the metalworking fluid in a major automotive engine plant to QUAKERAL® 381 SD, a new, more technologically advanced coolant. With the impact of this upgrade, Quaker was able to reduce the customer's processing costs by 25% and improve... Read More

Green & Clean, Lubricants

Water-Based Cable-Pulling Lubricant is 96% biodegradable.

Sep 16, 2010

Non-toxic, non-bioaccumulative, and chemically inert with low VOCs, Techni-Glide Lubricant contains microscopic poly-spheres that reduce surface contact, enabling smooth cable pulling, even under high sidewall bearing pressures. After drying, there is no sticky residue and product remains slippery. Low aquatic toxicity makes Techni-Glide suitable for marine and port installations as well as any... Read More

Lubricants, Materials & Material Processing

Momentive Introduces New Adjuvants for Agrochemicals at ISAA 2010

Aug 26, 2010

ALBANY, N.Y., August 19, 2010 - Building on a 70-year heritage of helping customers improve the performance of their products and bring new products to market, Momentive Performance Materials introduced two new adjuvants, Silwet* HS-604 penetrant and Silwet* STIK spreader-sticker, for agrochemical formulations at the ISAA (International Society on Adjuvants for Agrochemicals) 2010 in Germany.... Read More

Lubricants

Heat Sink Greases are formulated for thermal efficiency.

Aug 18, 2010

CircuitWorks® Boron Nitride Heat Sink Grease is thermally conductive grease, available in syringe dispenser for precision application. Engineered material provides optimal thermal conductivity for heat sinks with maximum electrical insulation. Throughout its rated thermal range of -99.4 to +392°F, silicone-free product will not harden or dry out. Read More

Lubricants, Portable Tools

Ergonomic Grease Guns include 18 Vdc and 120 Vac models.

Aug 17, 2010

Designed for heavy-duty applications, 18 V PowerLuber features output-optimized motor and battery technologies that unite to promote run time. Dual-speed transmission provides high-volume grease flow option. Along with torque-optimized motor, 120 V corded PowerLuber features variable-speed trigger and 2-speed transmission for precise flow control. Both guns, in addition to balanced design, have... Read More

Lubricants, Machinery & Machining Tools

QUAKERCOOL® Jumpstarts a Powertrain Manufacturer's Cost Savings

Aug 17, 2010

An Upgrade in Coolant Technology Raises the Bar on Process Performance CONSHOHOCKEN, Pa.- A major powertrain manufacturer was using an inferior, outdated soluble oil technology in four of its central coolant systems. After partnering with Quaker's CMS program to manage all chemicals, the facility chose to switch to a more technically advanced premium metalworking fluid. The quantified impact... Read More

Lubricants, Machinery & Machining Tools

Hybrid Metalworking Fluid offers microbial control.

Aug 04, 2010

Designed for moderate to heavy-duty operations, CIMTECH 609® is suitable for use with most aluminum alloys, titanium, exotic alloys, cast iron, carbon steels, high-speed steel, high alloy steels, and stainless steels. Product offers drawability and biological protection for use in recirculating systems. With no smoke and minimal residue, low-misting fluid leaves no slippery film on parts,... Read More

Lubricants, Machinery & Machining Tools

Metalworking Fluid supports milling and drilling operations.

Aug 04, 2010

Featuring hybrid blend of patented and synthetic lubricants, CIMTECH 610® provides synergistic performance on difficult-to-machine ferrous and non-ferrous alloys without corrosion or stain. Product is suited for use on hard, brittle metals, such as inconel, titanium, stainless steel, aerospace alloys, and hardened steel. Formulated without chlorine, sulfur, or phosphorous EP lubricants,... Read More

Lubricants

CIMCOOL's CIMTECH 310® Synthetic Metalworking Fluid Meets the Strict Requirements of Automotive Manufacturing

Aug 04, 2010

Cincinnati, Ohio - CIMCOOL, a long-time industry leader in metalworking fluid technology, offers CIMTECH 310®, a low pH synthetic fluid designed to meet the stringent requirements of the automotive industry. Passing all bi-metallic and aluminum (7075) "sandwich" corrosion tests, CIMTECH 310® has become the standard metalworking fluid for many automotive manufacturers. CIMTECH 310® is... Read More

Lubricants, Materials & Material Processing

One Automaker's Demand for Increased Productivity in Die Casting: How QUINTOLUBRIC® Helped

Jul 30, 2010

CONSHOHOCKEN, Pa., July 27, 2010 - In their die-casting operation, an automotive parts manufacturer was experiencing unacceptable amounts of downtime. High demands for performance and productivity were putting strains on equipment indicated by excessive pump and seal wear and poor component life. They began looking for a solution that would prolong their operating uptime. After technical... Read More

Lubricants

Synthetic Lubricant utilizes PTFE additives.

Jul 26, 2010

Formulated to withstand extreme temperatures of -40 to 450°F, Syntha-Tech(TM) Lubricant w/PTFE penetrates into cracks and joints to lubricate and protect all exposed metals. Non-flammable, zero-VOC product utilizes PTFE additives to minimize surface contact, friction, and wear, extending equipment life. Available in 16 oz aerosol can, food-grade product is NSF H1 Registered for use in meat and... Read More