Leg Levelers

Leg Levelers

Machinery Mounts suit pharmaceutical manufacturing equipment.

FDA approved H3A Series machinery mounts are made of ASNI 304 SS for chemical resistance, and feature rubber vulcanized to mount housing to provide hygienic seal. Operating from -20 to 100°C, leveling mounts have full range of motion starting at 10° pivot, providing secure footing and vibration control. Units are available with or without thread casings, with 1 or 2 anchoring holes,...

Read More »
Leg Levelers

Stainless Steel Machinery Mounts are FDA-approved.

Made of ANSI 304 stainless steel, H3A-Series hygienic leveling mounts feature 304 SS for chemical resistance and are rated for temperatures from -20 to +100°C. Products, suited for food and dairy processing equipment and manufacturing applications, are available with or without thread casings, which eliminate contamination and offer lock-nut functionality. Full range of motion, starting at...

Read More »
Leg Levelers

AirLoc ®Wedgmount Precision Levelers Save Days on Steam Turbine-Generator Install

Recently, Mr. Ross Hill, P.E., Project Manager for ESI of Tennessee approached AirLoc for assistance on an installation technique that could reduce or eliminate the grouting on a 5 MW, skid mounted, steam, turbine/gearbox generator. The standard" approach of grouting with a cementitious grout would take the better part of a day to construct forms, then a day to pre-soak the concrete, a day to mix...

Read More »
Stainless Steel Mounts level semiconductor equipment.
Leg Levelers

Stainless Steel Mounts level semiconductor equipment.

Stainless Steel AM-Series mounts for semiconductor manufacturing applications feature corrosive resistant design, swivel up to 7.5°, and have no hidden pockets where dirt and moisture can be deposited. Constructed with non-magnetic 304 grade stainless steel, mounts are also available in zinc-plated steel for environments where corrosion is not a factor.

Read More »
AirLoc Wedgmounts Provide Building Floor Load Support & Vibration Isolation
Leg Levelers

AirLoc Wedgmounts Provide Building Floor Load Support & Vibration Isolation

It is a common occurrence that upper floor loadings in existing buildings are changed with the installation of new and frequently heavier machinery. Therefore, existing floors may reach their load limits. In addition, there is danger of exciting critical vibration frequencies when floors, with low natural frequencies, are coupled with the disturbing frequencies of machinery supported on them. In...

Read More »
Leveling Mounts swivel 15° in all directions.
Leg Levelers

Leveling Mounts swivel 15° in all directions.

Offered in inch and metric sizes, NY-LEV Leveling Mounts come in steel and stainless steel stud type models, with or without lag holes. They feature glass-filled nylon plastic base and non-skid elastomer rubber pad that resists many organic acids, most chemicals, alkalines, salt, water, and corrosion. On steel mount, threaded stud with ball end and hex nut are zinc-plated steel while, on other...

Read More »
Leveling Mounts swivel to all sides for adjustment.
Leg Levelers

Leveling Mounts swivel to all sides for adjustment.

Made from carbon steel with gold iridite plated or black oxide finish, inch size Threaded Stud Type Level It Mounts have stud ball end machined from solid bar. Units swivel 7 Â-½Ã‚° to all sides of centerline to adjust to uneven surfaces and are suited for leveling machine tools, electronic racks, and benches. Mounts can be ordered with non-skid elastomer pads as well as elastomer cup...

Read More »
Platforms isolate equipment from surrounding vibrations.
Leg Levelers

Platforms isolate equipment from surrounding vibrations.

Available in custom sizes or shapes with extra leg supports and cutouts or notches, 9300 Series provides omni-directional, ultra-low-frequency vibration damping as well as automatic leveling. It is composed of 2 in. composite layer between Â-½ in. top and bottom plates of corrosion-resistant steel. At up to 25,000 lb load, vibration isolation efficiencies can be as high as 98% for vertical...

Read More »
Machine Mounts handle loads from 100-12,000 lb.
Leg Levelers

Machine Mounts handle loads from 100-12,000 lb.

Designed for equipment that does not require floor fastening, M-Series features built-in leveling bolt. Mounts provide direct leveling and insulate machinery against adverse effects of structure-born noise. Mechanically fastened nitrile pad is chemically resistant to most fluids and dampens up to 80% of machine or environmental vibration. Applications include automatic lathes, grinding machines,...

Read More »
Anti-Vibration Mounts feature stainless steel construction.
Leg Levelers

Anti-Vibration Mounts feature stainless steel construction.

AM 2100/4100 Series of machine mounts are designed for leveling and vibration damping in applications where moisture, liquids, and corrosive fumes come in contact with machinery. Carrying loads up to 4,000 lb, mounts feature shock absorbing, neoprene rubber soles to reduce vibration and to prevent creeping and walking in compliance with OSHA anchoring requirements. They can also adjust to pitched...

Read More »

All Topics