New Lasers Products

Micromachining Laser is designed for laboratory use.

IX-100 mini UV laser system brings laser photo-ablation into lab where various materials can be micro-machined with holes or complex patterns with precision near 1 micron. Laser provides 300 Hz repetition rate with 35 mJ/pulse at 248 nm energy, and can be tuned to operate at 193 nm by interchange of premix gas bottle and beam delivery optics. Custom-designed software controls all operations.

Yellow DPSS Lasers suit microscopy applications.

Operating at 561 nm, 85 YCA series diode-pumped solid-state (DPSS) lasers produce single-frequency output to 10 mW with less than 3% peak-to-peak noise. Beam is nearly circular, with less than 1.1:1 aspect ratio; is linearly polarized; and has M2 factor of less than 1.2. Compact, conduction-cooled laser head incorporates thermoelectric cooling and automatic power control. Lasers are suited for...

Green Pump Laser suits Ti:sapphire amplifiers.

Empower(TM) diode-pumped Nd:YLF laser, with 527 nm output, pumps Ti:sapphire amplifiers such as company's SpitfireÃ-® series. Q-switched laser delivers over 30 W at adjustable pulse repetition rates between 1-10 kHz, with pulse energies of over 20 mJ. With field-replaceable pump module, it utilizes intercavity frequency doubling and does not require external cooling water. Other applications...

Excimer Laser eliminates wafer scribing.

IX-1000 ChromaLift(TM) homogenizes laser beam profile and fires through back of sapphire wafer to de-bond GaN LED device and transfer it to substrate. Capabilities include large area-per-shot, either step and repeat or fire on-the-fly, of up to 1 x 1 cm area. Programmed via Windows 2000(TM) Software, system includes PC-controlled power meters and beam profilometer. It suits LED Lift-off...

A Solutions Provider

This white paper provides an overview of filtration and energy solutions.

Short Pulse Laser suits micromachining applications.

With fundamental wavelength of 1 micron, Staccato laser delivers 13 psec long, diffraction-limited pulses with peak power of 38 megawatts. It is available in harmonic wavelengths of 532, 355, and 266 nm. With UV wavelength, laser can have beam focused to spots of ~2 microns. Laser does not leave behind heat affected zone, operates at rates to 100,000 pps, and has 1 x 0.8 m laser head. Electronic...

Laser Cutting System utilizes rotary axis design.

Rotary axis on Impuls 4030 provides controlled manual or automatic support. Manual support mechanism uses fingers to securely position tube in flange, allowing one set of flanges to be used for different tubes within certain size range. Automatic support mechanism uses retractable arm to engage tube support and move device into desired position. When processing long tubes, both automated and...

Attenuator delivers precision laser intensity control.

Model UM-VA UV Excimer Laser Variable Beam Attenuator allows laser users to perform optics adjustments at low laser power settings for safer conditions. Dynamic range is nominally from 5-90% plus 100% transmission, while typical transmission range is less than 2% to greater than 94%. Variable transmission filter allows wide range of energy adjustment. Manual or motorized versions are available,...

Q-Switched Nd:YAG Lasers fit into small spaces.

Compact-Q Lasers provide 800 mJ per 6-8 ns pulse at 1064 nm with pulse repetition frequency of 10 Hz. They are offered with stable multimode, gaussian-coupled, or TEM00 resonator options. Mini-rail design allows them to be configured in oscillator, twin oscillator, and oscillator amplifier configurations with minimal change to laser head. Applications include PIV, LIF, LIBS, marking and drilling,...

Laser Podules provide output from 20-100 W.

Spectron diode-pumped, solid-state (DPSS) Laser Podules use side-pumped geometry, which consists of Nd:YAG-laser rod, located within stainless steel/ceramic pumping chamber, pumped by array of diode laser bars. Podules are driven by low-voltage electronics, ensuring that integration and certification is straightforward. Cooling is accomplished with water chiller.

Mini DPSS Lasers produce 5 W at 1064 nm.

Series SLD6000 low-powered, end-pumped, solid-state lasers feature direct diode coupling to Nd:YAG lasing media, providing TEM00 beam quality. Units include sealed laser head, field-replaceable diodes, as well as integral cooling, avoiding need for chillers. They offer high repetition rates, short pulses, and high peak powers for scribing, marking, inspection, and micromachining applications.