Interlock / Safety Switches

Interlock / Safety Switches

Point Level Switch offers SIL-certified overfill protection.

Safety IntelliPoint RF(TM) Switch, used in above-ground bulk storage tanks, meets American Petroleum Institute's 2350 Recommended Practice for overfill/spill protection. Specifically, it comes standard with SIL1 certification; SIL2 is optional, and SIL3 is possible with redundant switch. Integral software continuously monitors application for changes and maintains repeatable trip point on probe....

Read More »
Interlock / Safety Switches

Load Switch can handle continuous output current of 1 A.

With ability to operate under supply voltage range of 2.4-5.5 V, SiP4613A/B suits applications including load switching, battery switching, USB peripheral ports, hot-swapping, and power management applications. User-defined current limit level protects input supply voltage from excessive load currents. In shutdown mode, switch reduces supply current to less than 1 Â-µA. Available in Pb-free...

Read More »
Interlock / Safety Switches

Switch features built in serial and Ethernet networking.

Featuring built-in test/outage reporting, user-configurable alarms, and high-speed alarm capture capability, Zenith ZTE Series 40-4,000 A automatic transfer switch helps prevent problems that could damage equipment or cause unnecessary outages to critical loads. Auto Load Shed allows unit to signal for disconnection of downstream lower-priority loads in event of generator overload. Power quality...

Read More »
Interlock / Safety Switches

Adaptec Selects ConSentry Intelligent Switches as Best in Class Solution for Network Upgrade and Future Growth

ConSentry's Next-Generation Switching Architecture Delivers Operational Efficiency, Reduced Cost, Network Control and Visibility Milpitas, CA -January 28, 2008 - With the debut today of its Intelligent Switching architecture, ConSentry Networks announced that Adaptec, Inc. (NASDAQ: ADPT), a global leader in storage solutions, is deploying the ConSentry LANShield(tm) Switch as part of a total...

Read More »
Sanitary Flow Switch features non-intrusive design.
Interlock / Safety Switches

Sanitary Flow Switch features non-intrusive design.

Suited for control of liquids, specialty gases, or air in high-purity and sanitary processes, inline NuTecÂ-® FS2000L employs solid-state, temperature-compensated thermal mass flow sensor that installs flush inside pipe ID. General-purpose switch is available with electropolish finish of 20 or 10 Ra for service in line sizes from 0.5-2.0 in. It is accurate to Â-

Read More »
Door Handle System uses coded-magnets for safety.
Interlock / Safety Switches

Door Handle System uses coded-magnets for safety.

Rated IP67, tamper-resistant Series BNS-B20 may be used as combination door handle and safety interlock switch on hinged and sliding machine guards. Each unit consists of low-profile door handle assembly with 2 multiple reed switch arrays and coded-magnet actuators. Along with LED for switch status, product features 2 NC contacts, one NO contact, and M12x1 quick disconnect. Integral latching...

Read More »
Safety Switch features solenoid and LED signaling.
Interlock / Safety Switches

Safety Switch features solenoid and LED signaling.

Available in 2 signaling versions, Series FG Type A requires no external wiring and has LEDs switched on via solenoid power supply, while Type B allows connection to contact block, making it possible to control different states of switch. Metal-bodied switch features 3 conduit entries, actuator holding force of 2,500 N, integrated contact blocks with 4 poles, rotating head, and protection rating...

Read More »
Egress Bar employs weather-resistant design.
Interlock / Safety Switches

Egress Bar employs weather-resistant design.

Designed for environmentally unprotected areas, 6495 Series uses weather-resistant switch contacts and fits any standard 36 in. wide door; special widths are available for doors up to 48 in. wide. Single or dual contact outputs can be used for REX input to card access systems or EDR-101 Delayed Egress Systems. Imprinted with Push to Exit in black accent, aluminum egress bar has clear anodized...

Read More »
Interlock / Safety Switches

IEC Selector Switch increases component-level control.

Key-operated SensEject detects presence or absence of key in control equipment and automatically ejects key to prevent inadvertent or unauthorized operation. It prevents key retention in momentary positions and also allows user to work on specific equipment within production line without shutting down entire process. Key-sensing contact block can signal alarms or annunciators and detects when...

Read More »
Safety Interlock Switches offer 5 contact configurations.
Interlock / Safety Switches

Safety Interlock Switches offer 5 contact configurations.

Providing safety position detection of protective guards or doors, safety key-operated Series GKN features positive opening safety contacts and double insulation for global standard compliance. Rotating head allows actuator engagement from front, back, or either of 2 top positions for total of 4 different actuation entry points. Series offers choice of 3 standard key actuators, including flexible...

Read More »

All Topics