UltraFlex Demonstrates Hardening and Tempering of Alloy Steel Chains Using Induction
[Nov 2nd, 2018] UltraFlex Power Technologies recently published the results from yet another test application of induction heating for manufacturing purposes. In the test, industrial chains made up of alloy steel had to be hardened and tempered using induction heating, at temperatures of 1580˚F (860˚C) and 204˚F (400˚C) respectively. UltraFlex provides the most advanced digitally controlled...
Read More »
New Demonstration by UltraFlex Shows Bore Heating of a Steel Pipe Using Induction
[Oct 22nd, 2018] In pursuit of proving the limitless possibilities of induction heating for manufacturing purposes, UltraFlex Power Technologies has demonstrated how bore heating of a steel pipe could be achieved using induction heating. UltraFlex provides the most advanced digitally controlled induction heating solutions in the industry and is regularly coming up with proofs of how induction...
Read More »
UltraFlex Demonstrating Hardening of Push and Plane Rods Using Induction Heating, at Temperature 1508˚F - 1742˚F (820˚C - 950˚C)
[Oct 10th, 2018] UltraFlex - a leading induction heating solutions provider - has demonstrated the hardening of a push rod and plane rod using induction heating, at temperature of 1508˚F–1742˚F (820˚C – 950˚C). The hardening process is yet another application of induction heating demonstrated by UltraFlex engineers, using the company’s proprietary, advanced digitally controlled...
Read More »
UltraFlex Induction Heater Used to Harden a Steel Gun Barrel
[Sept 11th, 2018] New tests performed by UltraFlex Power Technologies revealed the results achieved when an induction heater was used for hardening of a 4140 steel gun barrel. The ultimate goal of the tests was to heat a small block section of a gun barrel to 1500◦F (815◦C) and quench it in oil, identifying the best possible induction coil and equipment settings for the process. An advanced...
Read More »
Guide to FDA Approval & Compliance
Manufacturers must comply with FDA rules and regulations to ensure public health.
Read More »
UltraFlex Heating Wires to 204
[May 2nd, 2018] UltraFlex - provider of the most innovative digitally controlled induction heating solutions in the industry - shared the results from their recent induction heating tests performed on wires with different diameter. Using the company’s proprietary induction heating equipment - an UltraHeat 10 kW power supply and a HS8LF Heat Station - UltraFlex successfully heated wires of 4...
Read More »
Un-Brazing and Re-Brazing Copper Angle Brackets to Copper Strips at 1400
December 4th, 2017 - The efficiency of UltraFlex Power Technologies Induction Heating systems has recently been demonstrated by the company’s engineers in a series of controlled tests. The goal of the tests was to evaluate the unbrazing and rebrazing capabilities of UltraFlex High Power Induction System from the UltraHeat L Series. Two sets of materials were used for the tests: a copper right...
Read More »
Reflowing Solder on Copper Boards in Less than 5 Seconds Using UltraFlex Induction Heating
November 17th, 2017 - UltraFlex Power Technologies recently demonstrated the excellent performance of their compact Induction Heating systems by showing how copper boards can get re-soldered within less than 5 seconds. A small copper connector board with dimensions 42mm x 17.5mm (1.65″ x 0.69″) and 3 pins on one side / 6 on the other had to be heated to 260°C (500°F) so solder on the board...
Read More »
eldec MICO Induction Heating Systems
Compact and Flexible, Stationary or Mobile, Efficient and Practical The MICO series' innovative design integrates the frequency converter and coolant system in a single housing. Small and compact, stationary or mobile, they are a flexible and practical solution for a wide range of uses including: induction brazing shrink fitting annealing die edge hardening curing Available in S (stationary), M...
Read More »
Ajax TOCCO Supplies Induction Billet Heating System
Ajax TOCCO Magnethermic recently shipped a 1000 kW PowerZone billet heating system to LC Manufacturing, located in Lake City, MI. The 1000 kW, 1.3 – 3.3 kHz system is designed to heat 1.06” to 2.875” diameter x 6.0” to 20.0” long carbon steel billets to forging temperatures. The system includes automatic changing of frequency for differing billet sizes. A PLC with touch screen display...
Read More »
Ambrell Sells EASYHEAT for Soldering Application
The induction system is being used to create a product for the industrial automation market Scottsville, NY- – Ambrell, a leading manufacturer of induction heating systems, has sold an EASYHEAT™ 6 kW, 150-400 kHz induction heating system to a manufacturer of industrial automation controls and sensors. The application involved heating six brass block and carbon contact assemblies to 242 -
Read More »
Delivery Equipment That Really Delivers
Are you in need of safer, more efficient transportation equipment? Do you feel like your delivery equipment could really use an upgrade? Check out this video, and learn about Halo Ramp Company's patented safety platforms, and how they help you bypass your trickiest delivery challenges.
Read More »
