Impeller eliminates rag buildup.
Solving problem of rag buildup in municipal and industrial treatment, CLEAN EDGE Impeller remains free of fibrous debris while delivering performance equal to hydrofoil impeller. After 9 months of continuous operation, impeller exhibited no rag buildup on diameter, had same power draw as when installed, and caused no mechanical issues while delivering required mixing.
Read More »Impeller eliminates rag buildup.
Solving problem of rag buildup in municipal and industrial treatment, CLEAN EDGE Impeller remains free of fibrous debris while delivering performance equal to hydrofoil impeller. After 9 months of continuous operation, impeller exhibited no rag buildup on diameter, had same power draw as when installed, and caused no mechanical issues while delivering required mixing.
Read More »
Motorized Impellers offer capacities to 5,060 cfm.
Offered in single or 3-phase voltages with dual frequency motors, Models TMK and TMK-H are equipped with BC airfoil wheel to provide quiet airflow. Units come in housed and non-housed models and are available with matching capacitors and inlet cones. Impellers are suited for variety of air-moving applications, including cooling of motor controls, electronics, power converter cabinets, and modular...
Read More »
Motorized Impellers offer capacities to 5,060 cfm.
Offered in single or 3-phase voltages with dual frequency motors, Models TMK and TMK-H are equipped with BC airfoil wheel to provide quiet airflow. Units come in housed and non-housed models and are available with matching capacitors and inlet cones. Impellers are suited for variety of air-moving applications, including cooling of motor controls, electronics, power converter cabinets, and modular...
Read More »
Seal Stuff In, Seal Stuff Out
One of the best ways to make sure that your machinery stays up and running in the face of adversity is to make sure that it's properly sealed. Of course, it's not always easy to determine whether the integrity of your seals are up to par. How can you tell when you have a problem?
Read More »Impeller is optimized for surface aeration applications.
Suited for higher-RPM wastewater applications in industrial/municipal facilities combating solids, sludge, rag, and increased volume challenges, Talon(TM) provides maximum oxygen transfer rate while achieving efficient mixing and biological nutrient removal. Curved, large-diameter design promotes flow and oxygen transfer with standard aeration efficiency of up to 4.5 lb O2/hp-hr. Product can...
Read More »Impeller is optimized for surface aeration applications.
Suited for higher-RPM wastewater applications in industrial/municipal facilities combating solids, sludge, rag, and increased volume challenges, Talon(TM) provides maximum oxygen transfer rate while achieving efficient mixing and biological nutrient removal. Curved, large-diameter design promotes flow and oxygen transfer with standard aeration efficiency of up to 4.5 lb O2/hp-hr. Product can...
Read More »Chemineer Announces New XE-3 Impeller
Dayton, Ohio - Chemineer has again set a new benchmark in high efficiency agitator impeller technology with the XE-3 impeller. Chemineer impeller designs are the result of over five decades of research and applied application experience, resulting in the broadest range of durable and efficient impeller options for its agitators. The Chemineer XE-3 impeller is as much as 24% more efficient than...
Read More »Chemineer Announces New XE-3 Impeller
Dayton, Ohio - Chemineer has again set a new benchmark in high efficiency agitator impeller technology with the XE-3 impeller. Chemineer impeller designs are the result of over five decades of research and applied application experience, resulting in the broadest range of durable and efficient impeller options for its agitators. The Chemineer XE-3 impeller is as much as 24% more efficient than...
Read More »
Hydrofoil Mixing Impeller optimizes fluid flow.
Available in 3-210 in. dia sizes, HYFLOW 218 Impeller features hydrofoil-style, 4-blade design with tapered blades that have narrow, low-pitch section at tip where speed is fastest and wider, higher-pitch section nearer hub where it is slower. Curved blades resist bending under stresses from fluid forces and also reduce drag. Impeller, made from 316 stainless steel, titanium, inconel, nickel, and...
Read More »
Hydrofoil Mixing Impeller optimizes fluid flow.
Available in 3-210 in. dia sizes, HYFLOW 218 Impeller features hydrofoil-style, 4-blade design with tapered blades that have narrow, low-pitch section at tip where speed is fastest and wider, higher-pitch section nearer hub where it is slower. Curved blades resist bending under stresses from fluid forces and also reduce drag. Impeller, made from 316 stainless steel, titanium, inconel, nickel, and...
Read More »
Don't Let Your Money Drain Down the Hole...Drill Steel with Euroboor
As a globally recognized manufacturer of industrial grade portable tools, Euroboor is at the forefront of drilling and cutting technology. Our reputation as an industry leader is built on robust products that fit a wide range of industrial cutting and drilling applications. See our video to learn more about all of our quality products.
Read More »
