Programmable Hot Plate features milled-flat aluminum top.
Other Process Heaters

Programmable Hot Plate features milled-flat aluminum top.

Suited for heating silicon wafers, electronic chips, displays, and adhesives, EchoTherm(TM) HP40A is programmed via front panel membrane switch and custom LCD. Digital unit can store 10 programs in memory of as many as 10 steps each, where each step includes temperature, temperature ramp rate, and time. Measuring 8 x 8 in., cast aluminum heater plates can be evenly heated from ambient to...

Read More »
Commercial Water Heaters are built for accessibility and capacity.
Water Heaters (HVAC)

Commercial Water Heaters are built for accessibility and capacity.

Available in models from 495,000-2,065,000 Btu/hr, Copper-Fin® water heaters use 2-pass heat exchanger and are rated for installation on combustible floors. Control panel, Building Management System connections, and other field connections are positioned on terminal boards at front of unit to facilitate installation and servicing. Also, operator interface panel provides 2-stage electronic...

Read More »
Electric Immersion Heaters have internal temperature regulation.
Immersion Heaters

Electric Immersion Heaters have internal temperature regulation.

SmartOne(TM) positive temperature coefficient electric immersion heaters utilize solid-state ceramic heating elements as heat source. Maximum temperature is internally limited regardless of operating conditions, whether units are operated in water, air, or surrounded by solids. With maximum output temperature below ignition point of most plastic tanks, products do not overheat even when covered...

Read More »
OK International Will Showcase Assembly and Rework Technology Advances at Nepcon China 2011
Smoke and Fume Extractors

OK International Will Showcase Assembly and Rework Technology Advances at Nepcon China 2011

The OK International team will display and demonstrate its full range of soldering and production assembly technologies at this year's Nepcon China in Shanghai, May 11 - 13. These industry-leading solutions will be fully operational at booth #1F10, including advanced soldering, desoldering and rework systems, programmable pre-heaters, fume extraction and a comprehensive range of dispensing...

Read More »
Solar Air Heater provides 80.7% peak solar efficiency.
Miscellaneous Collectors

Solar Air Heater provides 80.7% peak solar efficiency.

Featuring wall-mounted design that simulates glass-like facade, Lubi(TM) produces max output of 254 BTU/h/ftÂ-² and temperature increases of up 81°F above ambient outdoor temperatures, making it suitable for pre-heating outdoor air and supplemental heating of facilities. Each 3 x 1 ft polycarbonate panel has 906 perforations, which are dimpled and contoured to prevent rainwater...

Read More »
Flexible Transparent Heaters feature thin film design.
Flexible Heaters

Flexible Transparent Heaters feature thin film design.

Therma Klear Flex(TM) series heaters provide warmth needed for LCDs to operate in temperatures down to 0 to -40°C and for anti-fog, anti-icing, and de-icing of optics, sensors, and display assemblies. Products are constructed with single or multiple-layer conductive coatings with resistance from 5-200 WÂ-², which are applied to flexible optical-grade polyester. Typically 0.007 in....

Read More »
Presses

TMP Introduces High Temperature Composite Molding Line

Cleveland, Ohio - TMP Inc., A Division of French, a manufacturer of hydraulic press systems, has recently introduced a high temperature rapid heating oven and an automated high temperature composite molding press system. The design is a 500-ton, up to 1200°F press with an integrated material transfer system. The press can be designed with either 4-post or sideplate construction with a...

Read More »
Induction Heaters

Inductoheat, Inc.: 21 Systems Shipped and Order Is Complete

Madison Heights, MI - Inductoheat, Inc., the world's leading induction heating equipment manufacturer, shipped the last StatiScan® IV system of a 21 unit order. These customized systems were manufactured for a world leader in the mining and oil sands exploration and are being used for induction hardening and tempering drill rods and hardening pipe-end threads. For more information about...

Read More »
FTH Series Heaters
Immersion Heaters

FTH Series Heaters

Omega's new FTH series of flow through heaters are designed primarily for providing heat that regulates liquid temperature from 32 to 88 degrees Celsius (90 to 190 degrees Fahrenheit). The heaters have a titanium element that resists corrosion. The enclosure is made of ABS plastic and is water resistant. Perfect for Industrial Plants to maintain water temperature as it's pumped around the plant...

Read More »
Explosion-Proof Heater satisfies pressure vessel requirements.
Heaters

Explosion-Proof Heater satisfies pressure vessel requirements.

Able to be used with heat transfer fluids or in liquid cooling applications, horizontal Ruffneck(TM) AH Series features core design that makes heater compliant with Category H fittings regulations in Alberta, Canada (CSA B51). Models range from 115-440 V and 6,000-1,200,000 BTU/hr and feature 450 psi max operating pressure and 650°F max operating temperature. Extruded aluminum louvers...

Read More »
3Sixty Mission Critical Launches New Service Offering UPS as a Service As A Cost Effective Alternative to UPS Equipment Ownership
Sponsored

3Sixty Mission Critical Launches New Service Offering UPS as a Service As A Cost Effective Alternative to UPS Equipment Ownership

At 3Sixty Mission Critical, we specialize in maintaining the performance and uptime of our customer's mission-critical applications. Our services are comprehensive and designed to take on the entire burden of maintenance. Our "UPS as a service" is just another example of how we develop out of the box solutions to help our customers operate more efficiently; see our video to earn more.

Read More »

All Topics