
TOC Analyzer features detection limit of 4 ppb.
Measuring up to 25,000 ppm, Online TOC-Vc Analyzer enables multipoint calibration curve to be created from single high standard. Unit offers choice of data output via analog mode or RS232. Six contact outputs monitor status, errors, and alarms while contact inputs permit remote start, stop, calibration, and alarm reset. Analyzer is compatible with Total Nitrogen Module for simultaneous carbon and...
Read More »
Portable Gas Analyzer provides flue gas analysis.
Incorporating pipe pressure leak detector, draft and differential pressure meter, and 7 in. flue gas dual probe, Model BTU 2000+ analyzes O2, CO, and calculates CO2. Weighing 2 lb, unit has magnetic rubber shell for hands-free use, and also provides remote PLC communication capabilities. Other features include impact printer, gas sniffer, 250 test memory, and Windows-based software.
Read More »Software controls Varian 3900 gas chromatograph.
Control Software allows EZChrom Elite(TM) or OpenLAB(TM) to fully control 3900 GC with instrument control of GC and related autosamplers. Single software method provides data analysis and reporting as well as control of instrument running conditions. It supports instrument parameters such as split/splitless mode, multiple on column injectors, inlet temperature control, column oven temperature, as...
Read More »
Protocol Emissions Analyzers offer step-by-step operation.
With on-board CTM-34 test protocol, CA-CALC(TM) Series CA-6300 Compliance Protocol Emissions Analyzers guide operators through each step of combustion test process and print reports on-site. Products feature sample conditioner for hands-free, continual water removal and standard, low-maintenance emissions probe. Offered in 4 models, series also features factory-calibrated, field-replaceable...
Read More »
A Guide to Preventive Maintenance & Refurbishment of Your Tablet Press
Check out this guide to keeping your tablet press in good working order.
Read More »
Purge Monitor measures 0.01-25% oxygen with 0.01 resolution.
Portable Oxygen Analyzer, Model OM-4 measures oxygen levels for welding stainless steel pipes, tubes, and tanks to prevent coking, oxidation, and discoloration. It shows when oxygen has been removed down to 0.01%, indicating there are no leaks. Featuring large digital display, analyzer operates from internal, temperature-compensated, electrochemical oxygen sensor. Power is provided by 9 V...
Read More »
Flue Gas Analyzers include built-in sample pump.
Series 7200 offers continuous analysis of flue gas for any combination of O2, CO, CO2, NOx or combustibles from combustible processes burning clean fuel gas. With appropriate sample preconditioning, units can also measure sample gases from oil or coal-fired processes. Analyzers include digital readout for each gas, recorder output, automatic condensate removal, plus multiple gas and sample point...
Read More »
Flue-Gas Analyzer offers data logging and integral printer.
Lancom III measures COlow, CO high, O2, NO, NO2, NOx, SO2, H2S, CO2 and hydrocarbons. It calculates combustion efficiency, loss, excess air, CO2, and total NOx and provides measurement corrections such as oxygen normalization, wet or dry analysis, and automatic reading conversions. Insight software allows data capture, storage, analysis, and presentation of measurement information in...
Read More »Gas Monitor detects toxic chemicals and warfare agents.
Model ppbRAE Plus detects volatile organic compounds in concentrations of 1 part per billion. Photoionization feature extends its upper detection range from 200 parts per million up to 2,000 parts per million. Unit has self cleaning lamp and sensor to minimize need for maintenance and calibration, and resists moisture and dirt. More than 100 built-in correction factors enable unit to measure over...
Read More »
Air Analyzer enables atmospheric particulate monitoring.
Model 5020 Sulfate Particulate Analyzer supports need to measure ultra-low pollutant concentration levels in complex urban environments. System enables direct and automatic measurement of background air and produces near real-time data for improved monitoring programs. Analyzer features on-site setup and operation.
Read More »
Oxygen Analyzer suits high-temperature furnaces to 1,400°C.
Intrinsically-safe, In-Situ Analyzer, Model 5081FG utilizes zirconium oxide sensor cell to measure oxygen in process temperatures from 550-1400°C with accuracy of ±1.5% of reading. Since unit is mounted close to furnace or radiant section, it uses HART® protocol to deliver measurements, device status, and diagnostic data remotely to technicians. Applications include process...
Read More »
ISO-Certified J&D Tube Benders Delivers Rapid Tubeline Fabrication Services
J&D Tube Benders' laser cutting and machining services provide accurate and complex features on tubes of all shapes and sizes. Check out the video to learn more!
Read More »