Gas / Chemical Analyzers

Gas / Chemical Analyzers

Software controls Varian 3900 gas chromatograph.

Control Software allows EZChrom Elite(TM) or OpenLAB(TM) to fully control 3900 GC with instrument control of GC and related autosamplers. Single software method provides data analysis and reporting as well as control of instrument running conditions. It supports instrument parameters such as split/splitless mode, multiple on column injectors, inlet temperature control, column oven temperature, as...

Read More »
Protocol Emissions Analyzers offer step-by-step operation.
Gas / Chemical Analyzers

Protocol Emissions Analyzers offer step-by-step operation.

With on-board CTM-34 test protocol, CA-CALC(TM) Series CA-6300 Compliance Protocol Emissions Analyzers guide operators through each step of combustion test process and print reports on-site. Products feature sample conditioner for hands-free, continual water removal and standard, low-maintenance emissions probe. Offered in 4 models, series also features factory-calibrated, field-replaceable...

Read More »
Purge Monitor measures 0.01-25% oxygen with 0.01 resolution.
Gas / Chemical Analyzers

Purge Monitor measures 0.01-25% oxygen with 0.01 resolution.

Portable Oxygen Analyzer, Model OM-4 measures oxygen levels for welding stainless steel pipes, tubes, and tanks to prevent coking, oxidation, and discoloration. It shows when oxygen has been removed down to 0.01%, indicating there are no leaks. Featuring large digital display, analyzer operates from internal, temperature-compensated, electrochemical oxygen sensor. Power is provided by 9 V...

Read More »
Flue Gas Analyzers include built-in sample pump.
Gas / Chemical Analyzers

Flue Gas Analyzers include built-in sample pump.

Series 7200 offers continuous analysis of flue gas for any combination of O2, CO, CO2, NOx or combustibles from combustible processes burning clean fuel gas. With appropriate sample preconditioning, units can also measure sample gases from oil or coal-fired processes. Analyzers include digital readout for each gas, recorder output, automatic condensate removal, plus multiple gas and sample point...

Read More »
Flue-Gas Analyzer offers data logging and integral printer.
Gas / Chemical Analyzers

Flue-Gas Analyzer offers data logging and integral printer.

Lancom III measures COlow, CO high, O2, NO, NO2, NOx, SO2, H2S, CO2 and hydrocarbons. It calculates combustion efficiency, loss, excess air, CO2, and total NOx and provides measurement corrections such as oxygen normalization, wet or dry analysis, and automatic reading conversions. Insight software allows data capture, storage, analysis, and presentation of measurement information in...

Read More »
Gas / Chemical Analyzers

Gas Monitor detects toxic chemicals and warfare agents.

Model ppbRAE Plus detects volatile organic compounds in concentrations of 1 part per billion. Photoionization feature extends its upper detection range from 200 parts per million up to 2,000 parts per million. Unit has self cleaning lamp and sensor to minimize need for maintenance and calibration, and resists moisture and dirt. More than 100 built-in correction factors enable unit to measure over...

Read More »
Oxygen Analyzer suits high-temperature furnaces to 1,400°C.
Gas / Chemical Analyzers

Oxygen Analyzer suits high-temperature furnaces to 1,400°C.

Intrinsically-safe, In-Situ Analyzer, Model 5081FG utilizes zirconium oxide sensor cell to measure oxygen in process temperatures from 550-1400°C with accuracy of ±1.5% of reading. Since unit is mounted close to furnace or radiant section, it uses HART® protocol to deliver measurements, device status, and diagnostic data remotely to technicians. Applications include process...

Read More »
NO/NOx Analyzer uses chemiluminescent principle.
Gas / Chemical Analyzers

NO/NOx Analyzer uses chemiluminescent principle.

Model 300 CLD Analyzer continuously measures total concentration of oxides of nitrogen within gaseous sample. Method is based upon chemiluminescent reaction between ozone and nitric oxide (NO) to form nitrogen dioxide and oxygen. Features include 8 switch selectable ranges from 0-3 ppm to 0-10,000 ppm NO/NOx, critical flow orifice flow control, and digital diagnostics.

Read More »
Oxygen Analyzer features intrinsically safe design.
Gas / Chemical Analyzers

Oxygen Analyzer features intrinsically safe design.

In Situ Analyzer, Model 5081 FG utilizes zirconium oxide sensor cell constructed of ceramic materials to measure excess oxygen in process temperatures ranging from 1,022-2,550°F. HART® protocol delivers device status and diagnostic data via handheld infrared remote control to technicians servicing and calibrating systems. Mounted close to furnace or radiant section of process flue gas...

Read More »

All Topics