Gas and Chemical Sensors / Detectors

Leak Tester replaces helium in critical part testing.
Gas and Chemical Sensors / Detectors

Leak Tester replaces helium in critical part testing.

Designed for validating enclosures that must contain or exclude hazardous gases or liquids, Model M-1075-44 accommodates applications with leak rate limits specified as low as 10-4 sccs, and production volumes require testing of 7,000 parts/hr. It applies mass-flow technology using low-flow transducer, thermally isolated air reservoir, test chamber, and fixtures. During test process, VFD reports...

Read More »
Gas Detectors feature adjustable setpoints and alarms.
Gas and Chemical Sensors / Detectors

Gas Detectors feature adjustable setpoints and alarms.

Gas Detectors continuously monitor carbon monoxide, ammonia, LP/gasoline vapors, hydrogen, and combustible gas. Units are available for 115 Vac operation, battery operation with 3.6 V NiCad rechargeable battery, and remote 115 Vac operations. They include audible and visual alarm, failure and pilot signals, circuit test button, and alarm set check button. Sensor elements are explosionproof and...

Read More »
Infrared Detector monitors multiple gases.
Gas and Chemical Sensors / Detectors

Infrared Detector monitors multiple gases.

Hand-held Orion Plus IR Detector utilizes over 20 different sensors, including chemical, catalytic, and IR types. Functioning as personal monitor and pre-entry check device, unit detects combustible gases in atmospheric and inert applications. Backlit graphic display shows all gas readings at a glance, while text messages, LEDs, and audible alarm serve as additional alerts. Electrical Perma-Check...

Read More »
Multi-Gas Leak Detector works in production environments.
Gas and Chemical Sensors / Detectors

Multi-Gas Leak Detector works in production environments.

Designed to minimize operator error, Ecotec E3000 features I-Guide operator guiding-mode to ensure that correct number of locations on each unit under test is checked, and that each location is tested for predetermined minimum time. False alarms are reduced by algorithm which compensates for interfering background gases. Self-monitoring unit allows operator to verify unit is functioning properly...

Read More »
CO2 Transmitter works in HVAC applications.
Gas and Chemical Sensors / Detectors

CO2 Transmitter works in HVAC applications.

Suited for measuring CO2 in ventilation channels, EE85 features closed loop air stream and diaphragm that protect CO2 sensing cell from pollution. CO2 detection is based on non-dispersive infrared technology (NDIR), and aging effects are compensated by auto-calibration procedure. Available for measuring ranges of 0-2,000 ppm and 0-5,000 ppm, transmitter has compact design that facilitates...

Read More »
Toxic Gas Detection System provides stand-alone control.
Gas and Chemical Sensors / Detectors

Toxic Gas Detection System provides stand-alone control.

DMC Series gas and flame controller is available in 4 versions for continuous indication and alarm control of 4, 12, 24, or 36 channels. Each channel has selectable high and low level alarm setpoint, and all alarm or fault events are time and date-stamped. Supporting up to 4 I/O modules in one singular I/O module design, product accepts 4-20 mA inputs and can monitor contact input devices....

Read More »
Lead Analyzer is isotope-free.
Gas and Chemical Sensors / Detectors

Lead Analyzer is isotope-free.

Designed as point-and-shoot analyzer, handheld Inspector Series analyzes lead paint and other heavy metal contaminants on surfaces and wipes as well as in air, liquids, and soil. Unit, weighing less than 3.5 lb, uses X-ray tube in ergonomic handheld unit with pocket PC. It retrieves readings within 2-3 sec, and supplemental rear-facing display allows viewing from any angle. Using with PDA...

Read More »
Sensors and Controllers are configurable for gas monitoring.
Gas and Chemical Sensors / Detectors

Sensors and Controllers are configurable for gas monitoring.

Z Gard(TM) S Sensor detects presence of CO or NO2 in air. Sensors are available with 2 output versions, 4-20 mA analog output or addressable RS485 digital signal. Z Gard C Controllers are microprocessor based and interface with up to 40 remote sensors via RS485 serial communication ports. Z Gard COmbo Gas Monitor is available in 2 versions, either employing metal oxide solid-state sensor or...

Read More »

All Topics