Force Sensors / Transducers

Torque Transducer mounts in-line to SAE or Metric flanges.
Force Sensors / Transducers

Torque Transducer mounts in-line to SAE or Metric flanges.

Non-contact, rotary Model RTC sensor transmits torque signal to RF receiver, delivering output of 0 to 10 V, proportional to torque, or optional 4 to 20 mA output. Operating range is 1,500 to 170,000 in.-lb, with running speeds up to 15,000 rpm, depending on range. RF telemetry package is induction-powered by stationary loop antenna coupled to power supply and receiver. Transmitter may be...

Read More »
Torque Sensor communicates directly with PCs and laptops.
Force Sensors / Transducers

Torque Sensor communicates directly with PCs and laptops.

DAQ F/T 6-axis, force/torque transducer system includes transducer, interface board, power supply, data acquisition device, and software tools. Interface board on or near transducer produces 7-channel signal that can be read by most analog input data acquisition cards. Software has Windows ActiveX component that configures transducer system and converts raw voltages into force and torque.

Read More »
Transducer Simulator utilizes wire-wound resistors.
Force Sensors / Transducers

Transducer Simulator utilizes wire-wound resistors.

Model TS simulates millivolt-per-volt output of unamplified strain gauge transducer. Input resistance is field-selectable to 350 or 5000 ohms. Output is selectable in 5 ranges of 0.5, 1, 2, 5, and 10 mV/V, and each can be adjusted in 10% steps to simulate output of various transducers. Portable unit is enclosed in weatherproof aluminum case and needs no power supply. It draws its excitation...

Read More »
Torque Tranducers have capacities from 0.1 to 1500 Nm.
Force Sensors / Transducers

Torque Tranducers have capacities from 0.1 to 1500 Nm.

Model 1700 Series Rotary Torque Transducers are available with optional encoder for angle measurement or rpm option for speed monitoring. Body lengths vary from 62 to 84 mm. Contactless transmission of supply voltage and measuring signal enables continuous operation with low maintenance. They offer built-in instrumentation amplifier with +/-10 Vdc output, 100% mechanical overload protection, and...

Read More »
Combination System provides weight and force measurement.
Force Sensors / Transducers

Combination System provides weight and force measurement.

GS0/DPM-3 System is comprised of GS0 precision gram sensor and DPM-3 panel mount meter. It is suitable for variety of industrial and OEM force measurement and weighing applications. DPM-3 can be scaled to full 5 digits, samples 60 readings per second, provides analog output and features true peak reading capability. GS0 tension and compression sensor is offered in variety of ranges from 10 to...

Read More »
Torque Measuring Kit includes sensor and indicator.
Force Sensors / Transducers

Torque Measuring Kit includes sensor and indicator.

Combination kit includes SWS socket wrench torque sensor and PHM-100 portable handheld transducer indicator. Kit provides accurate measurements of bolt or nut wrenching torques in either direction, including breakaway torque. PHM-100 has peak hold that captures at less than 1 millisecond, and operates on one 9-V battery for 60 hours. SWS reaction type torque sensor is offered in 6 ranges from 10...

Read More »
Torque Sensors are designed for low torque applications.
Force Sensors / Transducers

Torque Sensors are designed for low torque applications.

STS2220 rotary shaft torque sensors are available in capacities from 1.0 to 10.0 Nm. They feature one-piece outer housings and pre-lubricated bearings, and accept either AC or DC excitation voltage for compatibility to most readout instruments. Units have 1.5 mV/V nominal output at rated capacity, bridge resistance of 350 ohms, maximum speed of 10,000 rpm, and non-linearity of +/- 0.1% of full...

Read More »
Sensor converts shaft to torque sensor in 15 minutes.
Force Sensors / Transducers

Sensor converts shaft to torque sensor in 15 minutes.

Model 1650B Snap-On Rotary Torque Sensor clamps onto drive train to take measurement data. It does not break into drive train to install in-line torque cell, and requires no professional installation. Model 1650B comes pre-calibrated. Installation requires users to clamp on 2 halves of sensor shell, position antenna, and connect wireless receiver. Available for shaft diameters from 2.5 to 15 in.,...

Read More »

All Topics