Impeller / Propeller / Turbine - Agitators / Mixers

Cutting System promotes flexible emulsification.

KS Cutting System provides flexible emulsifying solution for products incorporating extreme cold and high viscous raw materials to low-viscosity emulsions. Cutting set configuration simultaneously handles grinding, emulsifying, dispersing, and homogenization. Along with control over product temperature, system excels in extracting protein from meat to provide higher binding capabilities and...

Read More »
Centrifugal Screener features sanitary design.
Screening Separators

Centrifugal Screener features sanitary design.

Intended for food, dairy, pharmaceutical, and chemical applications, Centri-Sifter® features 3-bearing shaft that cantilevers for removal of internal components. External roller bearings located at motor end of shaft and on hinged cover at discharge end provide maximum support and vibration-free operation under heavy loads. Equipped with Clean-In-Place Spray Balls for rapid sanitizing using...

Read More »
Lines

Custom Rollforming Corp. Supplies Money-Saving Solar Racking to GREEN FUEL Technologies

MOUNDRIDGE, Kan. - Custom Rollforming Corp. (CRC), located in Moundridge, Kansas is a leading manufacturer of custom roll-formed products, recently supplied specially designed solar racking for a 300 kilowatt solar farm at Southwest Baking located in Tolleson, AZ. The assignment given Custom Rollforming Corp. by the solar farm contractor, GREEN FUEL Technologies, was to provide a durable racking...

Read More »
Cutters and Inserts hasten heavy-duty application feed rates.
End Mills

Cutters and Inserts hasten heavy-duty application feed rates.

Optimized for cuts of 1.250-4.000 in. dia, RHINO-FEED(TM) Heavy-Feed cutters and inserts allow for accelerated feed rates in moderate- to heavy-DOC and -FPT applications. Heavy-Feed 12 mm IC (inscribed circle) inserts have 4 usable edges and strong cross-section. End mills and shell mills feature top clamping strength suitable for heavier DOC (up to .060 in.) and larger machines, such as 50-taper...

Read More »
Wall Slotter cuts channels in concrete and masonry.
Slotting Machinery

Wall Slotter cuts channels in concrete and masonry.

Powered by 20 A motor with 7,500 rpm no-load speed, EMF 150 uses 2 adjustable, parallel, 6 in. diamond blades to cut channels up to 1 13/16 in. wide x 1 ¾ in. deep in concrete and masonry. Tool accommodates needs of plumbing, HVAC, and electrical renovations by allowing pipe, conduit, and wire to be placed inside walls and floors. Closed hood optimizes air flow and facilitates fragment...

Read More »
Refrigerant Dryers offer flow capacities from 10-5,000 cfm.
Dryers

Refrigerant Dryers offer flow capacities from 10-5,000 cfm.

With standard pressure dew point of 37°F, RA Series offers efficient method of drying compressed air. Aluminum heat exchanger features vertical profile that allows force of gravity to result in maximum droplet separation and self-cleaning. Varioflow hot gas bypass valve, which utilizes gas charged capsule that operates independently of power or electronic support, provides user with 100%...

Read More »
Controls and Controllers

Siemens Supplies Power Plant Components to India

Siemens Energy has received an order to supply the power train consisting of the key components for the combined cycle power plant Dhuvaran Phase III, in India. The purchaser is the Indian Engineering, Construction and Manufacturing multinational company Larsen & Toubro Limited, which is constructing the plant for the owner, Gujarat State Electricity Corporation Limited. Delivery of the...

Read More »
Turbines

GE's Frame 6FA Gas Turbines to Help Meet Growing Power Needs of Sabah, Malaysia

o Kimanis Power Project to Add 300 Megawatts of Electricity for the State of Sabah o CSA to Provide 18 Years of Service Support for the Plant KUALA LUMPUR, MALAYSIA - June 14, 2011 - GE (NYSE: GE) will supply three Frame 6FA gas turbines, associated generators and services for the 300-megawatt combined cycle gas-fired power plant project in Sabah, Malaysia. Using natural gas as its primary fuel,...

Read More »
Food Processors

Shaved Ice Machine is intended for smaller applications.

Designed for portability and to facilitate cleaning, No. 1886 Sno-Flake measures 22.8 x 20.2 x 10.3 in. and employs Â-¼ hp, 1,725 rpm motor to cut through ice. This UL- and Sanitation-Listed machine, which can be can be used for rentals, runs on 15 A plug and has LLDPE 3/16 in. thick cabinet that insulates ice for extended service capabilities.

Read More »
Vector® Sports Training Ball Offers Visible Point of Contact
Sponsored

Vector® Sports Training Ball Offers Visible Point of Contact

Our goal is to help every athlete derive maximum enjoyment from their sport and become a better player. We offer a line of innovative training tools that combine cutting-edge technology and out of the box thinking to deliver an unbeatable competitive advantage. The Vector® Sports Training Ball is just another example of our commitment to innovation. To learn how the Vector® is helping ballplayers everywhere, see our video.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers