Deflection Elbow Kits for Silo Top Fill Lines
Bethlehem, PA---New Smart Elbow® Deflection Elbow Kits from HammerTek® Corp allow direct replacement of silo top elbows and piping/tubing subject to abrasive wear, with all preparation done safely at ground level. Each kit contains all components required to replace failing elbows, including two Smart Elbow® deflection elbows and all necessary piping/tubing, connectors and gaskets. All can be...
Read More »New Pneumatic Conveying Elbows Offered in Cast Iron or Optional Stainless Steel
Gathers conveying air or gas in a round, rotating deflection zone that virtually eliminates destructive particle impact with the elbow wall. Effective for conveying abrasive, heat-sensitive and other powders, pellets, flakes and slurries. Available in seven different sizes to suit a wide range of material properties and throughput requirements.
Read More »New Pneumatic Conveying Elbows Offered in Cast Iron or Optional Stainless Steel
Gathers conveying air or gas in a round, rotating deflection zone that virtually eliminates destructive particle impact with the elbow wall. Effective for conveying abrasive, heat-sensitive and other powders, pellets, flakes and slurries. Available in seven different sizes to suit a wide range of material properties and throughput requirements.
Read More »Cold Expansion Pex Drop Ear Elbow consists of lead free brass.
F1960 Cold Expansion Pex Drop Ear Elbow is available in ½ (FIP) x ½ in. Pex size. Compliant to Safe Drinking Water Act (SDWA), unit features three ears.
Read More »Benefits of Interfacing Robots & People in the Supply Chain
Learn how robots generate safer operations, more accurate data, and greater flexibility.
Read More »Cold Expansion Pex Drop Ear Elbow consists of lead free brass.
F1960 Cold Expansion Pex Drop Ear Elbow is available in ½ (FIP) x ½ in. Pex size. Compliant to Safe Drinking Water Act (SDWA), unit features three ears.
Read More »ICE Series Inside Corner Elbow enables installations in inaccessible locations.
Used in ceiling installation for communications and power, hard-to-reach 90-degree bends under decks and below floors, ICE Inside Corner Elbow allows for multiple conduit runs which are to be installed in parallel without interference while accessing elbow’s cover. Providing smooth pulling surface for conductors to glide against, product enables for easy access when adding or removing cables...
Read More »ICE Series Inside Corner Elbow enables installations in inaccessible locations.
Used in ceiling installation for communications and power, hard-to-reach 90-degree bends under decks and below floors, ICE Inside Corner Elbow allows for multiple conduit runs which are to be installed in parallel without interference while accessing elbow’s cover. Providing smooth pulling surface for conductors to glide against, product enables for easy access when adding or removing cables...
Read More »Replacement Metric Flat Face Fittings
Replacement Fittings for Most Foreign Manufactured Equipment Mentor, OH, December 27, 2016 – Malone Specialty Inc., a quality manufacturer of industrial hose and hose fittings for over 30 years, is now manufacturing and stocking standard Metric Flat Face Fittings. Steve Malone, President of Malone Specialty Inc. stated, “For years we have been providing metric fittings and adapters use d by...
Read More »Replacement Metric Flat Face Fittings
Replacement Fittings for Most Foreign Manufactured Equipment Mentor, OH, December 27, 2016 – Malone Specialty Inc., a quality manufacturer of industrial hose and hose fittings for over 30 years, is now manufacturing and stocking standard Metric Flat Face Fittings. Steve Malone, President of Malone Specialty Inc. stated, “For years we have been providing metric fittings and adapters use d by...
Read More »Pulling Elbows make wiring pulls at right angles.
Manufactured in CF8M (316 SS), pulling elbows are designed for use with rigid conduit.These products, which make wiring pulls at 90° bends in conduit system, can assist in instances of sharp bends and allow straight pull in either direction. Each pulling elbow comes with Type 316 SS cover, neoprene gasket, and Type 316 SS screws.
Read More »Fresh Air Intake Designed to Meet ASHRAE 62.2 standards
Alan Manufacturing has a long history of developing innovative solutions for HVAC applications. With over 1,000 product designs under our belt, we have gained a reputation as the go-to source for HVAC dampers, hardware, duct supports, zone control systems, and much more. Adding to this extensive list of achievements we now announce the release of our new line of Fresh Air Intake products. Designed to meet ASHRAE 62.2 standards, they are the most robust and high-performance product of their kind. See our video to learn more.
Read More »