Fluid & Gas Flow Equipment

Pleated Filter meets ASHRAE 52.2 Standard.

Pleated Filter meets ASHRAE 52.2 Standard.

Type DP8 pleated panel filter has media made from 100% synthetic fibers enhanced with electrostatic charge to increase efficiency on particles sized one micron and below. It meets MERV8 rating per ASHRAE Standard 52.2 and provides 30-35% dust spot efficiency per ASHRAE Standard 52.1. Media is pleated with galvanized steel expanded metal backing to form consistently shaped pleats and prevent rust....

Read More »
Adhesive Dispenser is suitable for UV bonding processes.

Adhesive Dispenser is suitable for UV bonding processes.

Model 1500XL uses microprocessor-based timer and air regulator to control amount of UV-cure adhesive applied. Teach function makes it easy to determine correct amount of adhesive to use for any UV dispensing application. Deposit size can also be set with digital timer and fine-tuned in 0.1, 0.01 or 0.001 sec increments. To apply adhesive, user holds syringe like pen, places dispense tip in...

Read More »
Dispense System varies flow rate, shot size and mix ratio.

Dispense System varies flow rate, shot size and mix ratio.

Program-A-Shot 997 dispenses 2-component silicone, epoxy or urethane for potting or encapsulation applications. Flow rate, shot size and ratio can be electronically adjusted to mix and match parts on same production line without reprogramming system. For example, bar-code reader could identify part, then direct system to use programmed profile that dispenses material at pre-determined volume, mix...

Read More »
Underwater Pumps run in air or can be submerged.

Underwater Pumps run in air or can be submerged.

Model 893-09 or -10 pump has brushless 12 or 24 Vdc motor that can run in open air or fully submerged in water. Pump and motor are rated at 50,000 hr life, and produce 3 gpm at 1 ft head or 10.5 ft head at 0 flow. Pump comes with 3/8 in. OD smooth outlet and 3/8 in. female pipe thread inlet. Other size inlets and outlets for hose and threaded connections are available. Standard plastic components...

Read More »
Gear Pump Gears are available in herringbone style.

Gear Pump Gears are available in herringbone style.

Optional herringbone gears are available for extrusion, compounding, polymer extraction and transfer pumps. Gears increase discharge pressures, extend life of pump's parts, and provide equal bearing loading that reduces energy requirements, decreases temperature and shear to fluid, and decreases pulsations from gear pump. Applications include compounding, tape production, pipe production, polymer...

Read More »
Tiny Pumps dispense small amounts.

Tiny Pumps dispense small amounts.

SV700 Series of inert, solenoid-operated micro pumps are suitable for dispensing re-agents, dilutants and lubricants. Pumps are less than 3 in. high, have diameter of 1.10 in., and dispense volume of 50-250 -µL. Available with glass-filled polypropylene pump head and EPDM or viton elastomers, pumps are compatibile with wide range of fluids. Fluid connections include 1/4-28 flat bottom ports,...

Read More »
Filters are suitable for working pressure to 4500 psi.

Filters are suitable for working pressure to 4500 psi.

PL Series Manifold Mounted Filters are available in 9 different sizes, allowing user to select most suitable model for wide range of applications. Filter elements are synthetic micro-fibre available in 4 different filtration degrees, in standard and high collapse configurations. Filter housings allow for installation of differential, visual or visual-electrical clogging indicators.

Read More »
Molded High-Flow 2-Way Valve uses no O-ring end fittings.

Molded High-Flow 2-Way Valve uses no O-ring end fittings.

Created for use in high purity/corrosive chemical applications, injection-molded Furon® In-Line-1000 Valve provides true 1 in. orifice and angled actuator that promotes maximum flow (Cv-15). It is offered in pneumatically or manually actuated versions, and has maximum operating pressure and maximum back pressure ratings of 100 psi. Fluid temperature ranges from 40°F to 212°F. 1 in. Fine Thread...

Read More »
Coolant Nozzle fits machines and toolholders.

Coolant Nozzle fits machines and toolholders.

BlackEye has threaded hole which can be plugged with setscrew, making it suitable for toolholders with ports that occasionally need plugging. Nozzles are easy-to-aim replacement for brass balls which often move out of position while tightening lock-screw. To install, tighten lock-screw, then aim swiveling stainless steel ball with tip of Allen wrench. Rated to 150 psi, they are available in sizes...

Read More »
Pipe Fittings are designed for coolant nozzles.

Pipe Fittings are designed for coolant nozzles.

DualFit pipe fitttings fit both NPT and BSPT metric pipe threads, thus solving incompatability problems when using NPT pipe fittings on metric machine tools. Compact size is suitable for tight spaces. Acetal version is rated to 150 psi and brass version to 1500 psi.

Read More »

All Topics