Fittings

Compression Tube Fittings are rated at 15,000 psi.
Fittings

Compression Tube Fittings are rated at 15,000 psi.

Designed to eliminate cone and thread installation for fluid instrumentation users, rapid-assembly fittings come in 15 component shapes. Using compression sealing technique, they provide single-piece, vibration-resistant solution for common connection requirements. MPI tube fittings are available in sizes to suit tubing with ODs from Â-¼-¾ in. and include straight, 45°, and...

Read More »
Fittings and Valves help reduce required maintenance.
Fittings

Fittings and Valves help reduce required maintenance.

Made with 304 and 316L stainless steel materials, I-line series includes clamps, end caps, ferrules, elbows, tees, laterals, reducers, valves, and gaskets. Offered as alternative to flange-end stub joints, system consists of male and female ferrule, gasket, and heavy-duty wing nut style clamp. Bolted type clamp is also available for use in high-pressure applications. Products suit sanitary line...

Read More »
Structural Pipe Fittings can be used indoors or outdoors.
Fittings

Structural Pipe Fittings can be used indoors or outdoors.

Kee Klamp® slip-on fittings provide for side palm fixing of guardrails and balustrades to walls, ramps, steps, parapets, or other areas where railing is used. Model 68 features triangular wings and is available to fit Size 6, 7, and 8 pipe, while Model 115 features trapezoidal wings and fits same pipe sizes. Malleable, cast-iron pipe fittings feature case-hardened set screws and are...

Read More »
Flare Nut and Panel Mount Fitting prevent line rupture.
Fittings

Flare Nut and Panel Mount Fitting prevent line rupture.

ChemQuik® Dual Containment flare nut and panel mount flare fitting enable double containment of chemical handling fluid lines between coupling or fitting and CDU or pump. Weep port relieves pressure that builds between primary and secondary tubing in case of leak, or if chemical media permeates through primary line over time. Available in line sizes of Â-¼, ½, and ¾ in....

Read More »
Aluminum Fittings help construct stair rails.
Fittings

Aluminum Fittings help construct stair rails.

Kee Lite® L29 and L30 corrosion-resistant, slip-on pipe fittings are angled and adjustable for use in construction of stair rails and safety railings. They fit standard pipe Size 7 and Size 8 for 1Â-¼ and 1½ in. diameter pipe, respectively. Suited for struts and braces, Model L29 may be adjusted for any angle between 30-60°. Used as slope between mid-rail and intermediate...

Read More »
Fittings

Monel Grease Fittings withstand harsh environments.

Monel fittings provide corrosion and temperature resistance in severe operating conditions such as military equipment, pulp & paper mills, chemical processing plants, oil processing equipment, and marine applications. Monel fittings provide higher strength and greater resistance than 316 stainless steel when exposed to seawater, brackish water, or high-temperature steam. Operating temperature...

Read More »
Expansion Joint overcomes temperature swings.
Fittings

Expansion Joint overcomes temperature swings.

PVC and CPVC Expansion Joints suit applications where air or fluid can experience 30°F shift in temperature. Inner and outer telescoping tubes allow mounting between 2 fixed points. Inner tube expands and contracts against anchored outer tube to provide flexibility, while triple O-ring design enhances strength and rigidity. Operating ambient temperature range is from 60-90°F, and...

Read More »
Pneumatic Fittings come in push-to-connect style.
Fittings

Pneumatic Fittings come in push-to-connect style.

Push-to-connect pneumatic fittings allow instant connections to be made by pushing tube into fitting; no tools or other operations are necessary. Suited for mobile and in-plant applications involving compressed air, products are available in body designs and configurations measuring 1/8-1/2 in. in dia. Fittings, offered in poly and nickel-plated brass, are also offered for metric tubes with BSP...

Read More »
Push-Fit Fittings suit compressed air systems.
Fittings

Push-Fit Fittings suit compressed air systems.

Push-Fit Fittings and Pipe provide connection from compressor receiver to take off points for point-of-use equipment. Since all connections are made with push-in action, there is no need to prepare threaded pipe or apply solvent. Systems can be easily disconnected, allowing for modification or expansion. Fittings are plastic or brass and are used with nylon, copper, or aluminum pipe.

Read More »
Tube Fittings work in pneumatic and water circuits.
Fittings

Tube Fittings work in pneumatic and water circuits.

All-metal WeldFit fittings help reduce assembly times and provide quick disconnection to enable re-tubing of system if it needs to be changed. Nickel-plated products feature silicone free O-rings and provide system protection from weld spatter. Rated for operating temperatures from -20 to 160°F, fittings are used in conjunction with WeldTube. Counterbored collet head provides complete...

Read More »
Solder Redefined
Sponsored

Solder Redefined

Indium Corporation has developed a new twist on traditional solder by developing a composite with a reinforced matrix internal structure. The result is a solder with increased strength and reliability. Check out this video to learn more about the mechanics behind the groundbreaking technology.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers