New Fittings Products

Cord Fittings terminate multiple wires into one connector.

Nonmetallic, Multi-Hole, Cord Grip Fittings meet industry demand for panel connections that save panel space. They are IP68 rated, UL listed, and VDE rated for European applications. Available with 2-, 3-, and 4-hole grommets, units feature temperature range of -86 to 176?F.

Compression Tube Fittings are rated at 15,000 psi.

Designed to eliminate cone and thread installation for fluid instrumentation users, rapid-assembly fittings come in 15 component shapes. Using compression sealing technique, they provide single-piece, vibration-resistant solution for common connection requirements. MPI tube fittings are available in sizes to suit tubing with ODs from Ã-¼-Ã-¾ in. and include straight, 45Ã-

Fittings and Valves help reduce required maintenance.

Made with 304 and 316L stainless steel materials, I-line series includes clamps, end caps, ferrules, elbows, tees, laterals, reducers, valves, and gaskets. Offered as alternative to flange-end stub joints, system consists of male and female ferrule, gasket, and heavy-duty wing nut style clamp. Bolted type clamp is also available for use in high-pressure applications. Products suit sanitary line...

Structural Pipe Fittings can be used indoors or outdoors.

Kee KlampÃ-® slip-on fittings provide for side palm fixing of guardrails and balustrades to walls, ramps, steps, parapets, or other areas where railing is used. Model 68 features triangular wings and is available to fit Size 6, 7, and 8 pipe, while Model 115 features trapezoidal wings and fits same pipe sizes. Malleable, cast-iron pipe fittings feature case-hardened set screws and are...

Metal Stamping for Construction Tool Applications

Metal stamping is a highly versatile manufacturing technique, capable of producing quality components at tight tolerances.

Flare Nut and Panel Mount Fitting prevent line rupture.

ChemQuikÃ-® Dual Containment flare nut and panel mount flare fitting enable double containment of chemical handling fluid lines between coupling or fitting and CDU or pump. Weep port relieves pressure that builds between primary and secondary tubing in case of leak, or if chemical media permeates through primary line over time. Available in line sizes of Ã-¼, Ã-½, and Ã-¾ in. OD,...

Aluminum Fittings help construct stair rails.

Kee LiteÃ-® L29 and L30 corrosion-resistant, slip-on pipe fittings are angled and adjustable for use in construction of stair rails and safety railings. They fit standard pipe Size 7 and Size 8 for 1Ã-¼ and 1Ã-½ in. diameter pipe, respectively. Suited for struts and braces, Model L29 may be adjusted for any angle between 30-60Ã-

Monel Grease Fittings withstand harsh environments.

Monel fittings provide corrosion and temperature resistance in severe operating conditions such as military equipment, pulp & paper mills, chemical processing plants, oil processing equipment, and marine applications. Monel fittings provide higher strength and greater resistance than 316 stainless steel when exposed to seawater, brackish water, or high-temperature steam. Operating temperature...

Expansion Joint overcomes temperature swings.

PVC and CPVC Expansion Joints suit applications where air or fluid can experience 30Ã-

Pneumatic Fittings come in push-to-connect style.

Push-to-connect pneumatic fittings allow instant connections to be made by pushing tube into fitting; no tools or other operations are necessary. Suited for mobile and in-plant applications involving compressed air, products are available in body designs and configurations measuring 1/8-1/2 in. in dia. Fittings, offered in poly and nickel-plated brass, are also offered for metric tubes with BSP...

Push-Fit Fittings suit compressed air systems.

Push-Fit Fittings and Pipe provide connection from compressor receiver to take off points for point-of-use equipment. Since all connections are made with push-in action, there is no need to prepare threaded pipe or apply solvent. Systems can be easily disconnected, allowing for modification or expansion. Fittings are plastic or brass and are used with nylon, copper, or aluminum pipe.

Tekna Manufacturing LLC Announces NFPA 99 Compliant Model 7200 Multiplace Chamber

Tekna is a leader in Monoplace and Multiplace Hyperbaric Chambers for Hyperbaric Oxygen Therapy (HBOT), offering products that set the standard for quality and innovation. Our new 7200 series of multiplace chambers is a state-of-the-art system that integrates advanced engineering with a plethora of features and options making it the industry's premier HBOT system. To learn more, see our video.