ADI Improves T-4 Adjustable Linear Feeder
Erie, Pa. - Bob Hoover, Feeder Technician in Automation Devices' VFC Division, has developed a fully adjustable linear feeder that conveys very small parts through vibration. In the past, each linear feeder manufactured was strictly dedicated to a specifically designed track with a specific weight and length. Any alteration in length or weight could drastically de-tune the feeder causing poor...
Read More »
Gravimetric Feeder offers feed rates up to 212 cu-ft/hr.
Intended for extruder manufacturers and compounders, ProFlex-® C Model 6000 comes equipped with asymmetric flexible PUR feed-hopper and 8-point external agitation system that can be adjusted without influencing screw speed. Angular cut discharge nozzle optimizes accuracies by minimizing pulsation at low speeds. Integrated, dual strain gauge load cell-based multi-point weighing system serves as...
Read More »
Gravimetric Feeder offers feed rates up to 212 cu-ft/hr.
Intended for extruder manufacturers and compounders, ProFlexÃ-® C Model 6000 comes equipped with asymmetric flexible PUR feed-hopper and 8-point external agitation system that can be adjusted without influencing screw speed. Angular cut discharge nozzle optimizes accuracies by minimizing pulsation at low speeds. Integrated, dual strain gauge load cell-based multi-point weighing system serves...
Read More »Part Pre-feed Hopper/Elevators
CDS Part Pre-feed Elevators are designed for the steady metered flow of parts being loaded into automated assembly and packaging machinery. An innovative hopper design insures constant parts flow and is well suited for feeding tubes, caps and closures for pharmaceutical, medical, cosmetic and other high profile products. Meets GAMP industry standards & Clean Room" requirements. Ergonomic floor...
Read More »
Reflective Tapes and Their Visibility Control Applications
This ebook provides an overview into reflective tapes and their visibility control applications.
Read More »Part Pre-feed Hopper/Elevators
CDS Part Pre-feed Elevators are designed for the steady metered flow of parts being loaded into automated assembly and packaging machinery. An innovative hopper design insures constant parts flow and is well suited for feeding tubes, caps and closures for pharmaceutical, medical, cosmetic and other high profile products. Meets GAMP industry standards & Clean Room" requirements. Ergonomic floor...
Read More »
Vibratory Bowl Feeder is designed for feeding pen caps.
Ensuring lightweight plastic pen caps are fed in correct orientation, Vibratory Bowl Feeder provides high speeds of more than 100 pieces/min for 40 mm length caps. Unit features gravity chute designed to maintain clip orientation. Bowl is made of cast aluminum with Elscinthane PU coating in green color, while tooling is made in stainless steel with full argon welding.
Read More »
Vibratory Bowl Feeder is designed for feeding pen caps.
Ensuring lightweight plastic pen caps are fed in correct orientation, Vibratory Bowl Feeder provides high speeds of more than 100 pieces/min for 40 mm length caps. Unit features gravity chute designed to maintain clip orientation. Bowl is made of cast aluminum with Elscinthane PU coating in green color, while tooling is made in stainless steel with full argon welding.
Read More »Sheet Feeder can feed up to 15,000 sheets/hr.
Featuring air-table design that allows its operator to load/center stacks of collated sets from stack carts, Bourg BSF sheet feeder automatically transfers paper from different manufacturers' printers and stack carts while maintaining integrity of collated sets for production finishing. Equipped with 2 feeding compartments that accept pile heights of 20 in. for primary content and up to 6.3 in....
Read More »Sheet Feeder can feed up to 15,000 sheets/hr.
Featuring air-table design that allows its operator to load/center stacks of collated sets from stack carts, Bourg BSF sheet feeder automatically transfers paper from different manufacturers' printers and stack carts while maintaining integrity of collated sets for production finishing. Equipped with 2 feeding compartments that accept pile heights of 20 in. for primary content and up to 6.3 in....
Read More »
Gravimetric Feeder offers extrusion following option.
Designed to feed colorants and additives into plastics processing machines, Maguire-® MGF(TM) Feeder includes multilingual operator access and full data retrieval as standard. Installed in controller, optional extrusion following system monitors a or dc voltage output from tachometer, and since output varies with extruder rpm, controller instantly senses gross changes in extruder speed and...
Read More »
Fresh Air Intake Designed to Meet ASHRAE 62.2 standards
Alan Manufacturing has a long history of developing innovative solutions for HVAC applications. With over 1,000 product designs under our belt, we have gained a reputation as the go-to source for HVAC dampers, hardware, duct supports, zone control systems, and much more. Adding to this extensive list of achievements we now announce the release of our new line of Fresh Air Intake products. Designed to meet ASHRAE 62.2 standards, they are the most robust and high-performance product of their kind. See our video to learn more.
Read More »
