Feeder streamlines SMT pin placement on multiple platforms.
AutoFeeder(TM) supports placement of SMT pins and other interconnects on existing pick-and-place equipment. Primary transport mechanisms and component handling functions are matched directly to existing feeder mounting methodology used by major equipment manufacturers to create seamless interface for each SMT placement platform. AutoFeeder handles continuously reeled components including...
Read More »
Glass Quenching Feeder operates in corrosive atmospheres.
Vibrating Glass Quenching Feeder is 18 in. wide by 17 ft long with bolt-in, abrasion-resistant, chrome-carbide overlay quench trough. It features wear-resistant liner, corrosion resistant epoxy paint system, and corrosion resistant rubber isolation springs for minimizing vibration transmission. Water-proof TENV vibrating motors have adjustable eccentric weights for retention control.
Read More »
Glass Quenching Feeder operates in corrosive atmospheres.
Vibrating Glass Quenching Feeder is 18 in. wide by 17 ft long with bolt-in, abrasion-resistant, chrome-carbide overlay quench trough. It features wear-resistant liner, corrosion resistant epoxy paint system, and corrosion resistant rubber isolation springs for minimizing vibration transmission. Water-proof TENV vibrating motors have adjustable eccentric weights for retention control.
Read More »
Wire Feeders run hard/cored wires at speeds of 50-780 ipm.
70 Series semi-automatic, constant-speed welding wire feeders are offered in bench top dual wire and Swingarc(TM) boom-mounted versions. Bench dual wire models feature spool capacity of 60 lbs (per side), independent controls, and separate meters. Swingarc boom-mounted 70 Series feeders' controls are placed at 12 or 16 ft boom's base, and drive assembly is at end of 360 deg rotating boom. Boom...
Read More »
Hemp: An Eco-friendly Substitute for Cotton and Petroleum-based Synthetics
To learn more about hemp's history, composition, performance, and its sustainability and cost, download this white paper now.
Read More »
Wire Feeders run hard/cored wires at speeds of 50-780 ipm.
70 Series semi-automatic, constant-speed welding wire feeders are offered in bench top dual wire and Swingarc(TM) boom-mounted versions. Bench dual wire models feature spool capacity of 60 lbs (per side), independent controls, and separate meters. Swingarc boom-mounted 70 Series feeders' controls are placed at 12 or 16 ft boom's base, and drive assembly is at end of 360 deg rotating boom. Boom...
Read More »Feeders, Indexers, and Accumulators are plug and play.
Glidepath(TM) system of assembly line feeders, indexers, and accumulators are suitable for automated introduction of components for industrial assembly processes. Systems include fall-away stop coupled to Sure Start nudger, which pushes conveyed unit on downstroke of stop without additional controls, thus eliminating additional operator intervention.
Read More »Feeders, Indexers, and Accumulators are plug and play.
Glidepath(TM) system of assembly line feeders, indexers, and accumulators are suitable for automated introduction of components for industrial assembly processes. Systems include fall-away stop coupled to Sure Start nudger, which pushes conveyed unit on downstroke of stop without additional controls, thus eliminating additional operator intervention.
Read More »
Welding Products include power sources, drives, and feeders.
CST(TM) 250 Stick/TIG power source provides 250 A for stick and TIG welding. CST Rack for multiple operators can hold up to 4 welding units. Bobcat(TM) 250 NT engine driven welding generator's rated output in CC/DC/AC mode is 250 A at 25 V, 100% duty cycle. 70 Series constant-speed wire feeders are available in bench-top, boom-mounted, and single- and dual-wire configurations.
Read More »
Welding Products include power sources, drives, and feeders.
CST(TM) 250 Stick/TIG power source provides 250 A for stick and TIG welding. CST Rack for multiple operators can hold up to 4 welding units. Bobcat(TM) 250 NT engine driven welding generator's rated output in CC/DC/AC mode is 250 A at 25 V, 100% duty cycle. 70 Series constant-speed wire feeders are available in bench-top, boom-mounted, and single- and dual-wire configurations.
Read More »
Vibratory Feeder has 3 mounting options.
Model 68B Heavy-Duty Feeder features suspended 24 x 42 in. tray anchored to below-deck drive with rated capacity of 275 tph (when installed at 10-º slope). Its dust-tight, epoxy-coated, heavy-duty, electromagnetic AC drive ships with N12 solid-state 100% variable speed control unit. Suitable for handling aggregates, slag, coal, ores, or grains, model 68B is available with open and tubular trays...
Read More »
SEALTITE® Fittings and Cord Grips Offer Longer Lasting Protection
Anamet Electrical's 316 Stainless steel SEALTITE® fittings and UL-listed cord grips protect sensitive wiring components from fluids, corrosive contaminations, bumps, and abrasions with a steel core and liquid tight conduit jacket. Check out this video to learn more.
Read More »
