Epoxies

Sealant has -300 to 600°F service temperature range.
Epoxies

Sealant has -300 to 600°F service temperature range.

One component, heat curing epoxy adhesive/sealant EP17 cures at temperatures from 300-350°F for 60-90 minutes. Flowable paste has 8,700 psi tensile strength, 387,000 psi tensile modulus, Shore D hardness greater than 90, and compressive strength greater than 13,000 psi. MIL-MMM-A-132 compliant, 100% reactive compound is resistant to chemicals, including fuels and acids, and bonds to metals,...

Read More »
Two-Part Epoxy features low exotherm during cure.
Polymers

Two-Part Epoxy features low exotherm during cure.

Master Bond Polymer System EP37-3FLSP bonds to substrates such as metals, glass, ceramics, plastics, and elastomers. Optically clear epoxy features electrical insulation properties and exhibits resistance to vibration, shock, and thermal cycling. Suited for large-volume castings, product has 20 Shore D hardness, 1,000 psi tensile strength, and over 400 V/mil dielectric strength. Pot life after...

Read More »
Epoxy Adhesive meets NASA low outgassing specifications.
Epoxies

Epoxy Adhesive meets NASA low outgassing specifications.

Formulated to setup in 3-5 min in 10-20 g masses at room temperature, EP65HT-1 ultra-fast curing, high temperature resistant epoxy adhesive bonds with metals, glass, ceramics, woods, vulcanized rubbers, and plastics. It has Shore D hardness of >75 and volume resistivity of >1014 ohm-cm. Mixed viscosity is 60-70,000 cps and mix ratio is 10 to 1 by weight. Available in pint, quart, gal, and 5 gal...

Read More »
Epoxies

Adhesive and Epoxy are designed for flip chip assembly.

Material GPC-251A/B is silver-filled, electrically conductive, 2-part, room-temperature curing adhesive used to connect bumps on underside of circuit boards. Product cures in 24 hr @ 25°C, 60 min @ 65°C, and 5 min @ 120°C. Material 123-38A/B-187 is thermally conductive underfill epoxy that strengthens chip package, protecting it from moisture and adding mechanical strength....

Read More »
Repair Epoxy forms machinable aluminum layer.
Epoxies

Repair Epoxy forms machinable aluminum layer.

Packaged in pre-measured job sized kits, 450°F Machine-IT features sticky consistency that holds assemblies or parts together while curing. Product offers adhesion to smooth, rough, or porous surfaces, and most plastics, metals, ceramics, glass, and wood. Curing in 2-4 hours, epoxy forms hard, metallic composite that can be machined, tapped, drilled, and threaded. Machine-IT is suited for...

Read More »
Repair Compounds

Low Viscosity Adhesive offers Tg of 90°C.

TRA-BOND F110 is optically clear, low viscosity adhesive. Two-part epoxy can be room temperature or heat cured, and provides thin bond line on applications involving prisms, lenses, and other optical components. Adhesive exhibits wicking and wetting characteristics, offers high strength structural bond, and bonds to glass, ceramics, metals, and most rigid plastics.

Read More »
Epoxies

Epoxy Adhesive features low viscosity.

TRA-BOND F113SC epoxy adhesive is formulated for fiber optics, LED displays, lenses and other optical components. It provides high bond strength and low stress connections with no pistoning. Featuring Tg of 95°C, 2-part rigid epoxy system is curable at room temperature or can be heat cured in 15 min. It exhibits low water absorption percentage.

Read More »
Epoxies

Epoxy Adhesive has tensile shear strength of 2,000 psi.

Two component, room temperature curing, nickel filled, electrically conductive EP76M epoxy adhesive features thermal conductivity of 8-9 Btu/in/ftÂ-²/hr/°F. Featuring one to one mix ratio by weight or volume, it offers 5-10 ohm-cm volume resistivity. EP76M exhibits 30 in/in x 106/°C thermal expansion coefficient, and service operating temperature range of -60 to +250°F....

Read More »
Instant Metal bonds, repairs, and rebuilds.
Coatings

Instant Metal bonds, repairs, and rebuilds.

Packaged in dispensing cartridges, 450°F Instant Metal 7056AL forms solid metallic aluminum layer that adheres to smooth, rough, or porous surfaces as well as most plastics, metals, ceramics, glass, and wood. It cures in 4-8 min at room temperature without objectionable sulfur odors. Once cured, metallic composite is machinable with standard tools and can also be tapped, drilled, and...

Read More »
Resins

Polymer Adhesive has flexible, low-viscosity formula.

Designed for bonding, sealing, and casting engineering plastics and metals, EP40 cures at ambient or elevated temperatures with 1:1 mix ratio by weight or volume. Flexible, 2-component epoxy resin compound is resistant to thermal cycling as well as mechanical vibration and shock. Shear and peel strengths for bonding polycarbonates are 1000 psi and 20 pli, respectively, while steel and aluminum...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers