Epoxies

Epoxy Adhesive offers impact and vibration resistance.
Epoxies

Epoxy Adhesive offers impact and vibration resistance.

One-component, electrically conductive 40-3910 is formulated for electrical and mechanical bonding of semiconductor, capacitor, and resistor chips in micro and opto-electronic hybrid circuit fabrication. Product does not require dry ice during transit and cures quickly at low temperatures. It provides optimized retention of strength after environmental aging.

Read More »
Epoxies

Huntsman Introduces New Araldite® Epoxy Insulating Systems at IEEE - PES

THE WOODLANDS, Tex., April 21, 2008 - A new family of Araldite® hydrophobic cycloaliphatic epoxies (HCEP) specially formulated to perform in extreme climatic environments was introduced to the U.S. market today at Huntsman Advanced Materials' IEEE PES Transmission and Distribution Conference and Exposition Booth 123/124. Araldite® HCEP systems are ideal for the construction and insulation...

Read More »
Coatings

High-Solids Epoxy targets marine applications.

Free of hazardous air polluting solvents, anti-corrosive SeaGuard 6200 can be applied at temperatures as low as 20°F, making it suited for vessel maintenance during winter lay-up. Product may be used on many prepared steel substrates, including bilges and wet void areas, decks and superstructures, and underwater hulls. Applied by brush, roller, or spray, coating is suited for fabrication...

Read More »
Epoxies

Low-Expansion, Low-Odor Epoxy cures at room temperature.

Resistant to electricity, chemicals, and moisture, Duralco(TM) 4463 is 100% solid system that exhibits dimensional stability and adheres to glass, ceramics, metals, and plastics. This 500°F epoxy, suited for bonding and encapsulating applications, contains no VOCs and only requires users to mix and apply.

Read More »
Epoxy Resin offers dimensional stability.
Resins

Epoxy Resin offers dimensional stability.

Suited for bonding, encapsulation, and coating, 2-component EP21LM-3 develops tensile modulus greater than 100,000 psi and tensile shear strength greater than 2,300 psi. Viscosity of 37,000 cps enables product to flow evenly and smoothly without application of pressure. When cured, polymer has Shore D hardness of 64 and resists thermal cycling as well as water, oil, fuels, and most organic...

Read More »
Epoxies

Adhesives are suited for magnet bonding.

Loctite® 331(TM) Structural Adhesive is acid-free, 2-step acrylic that fixtures in 20 sec and develops full strength in 30 min, bonding magnets and metals of all sizes. Designed for filling large gaps, Loctite® 3060(TM) Structural Adhesive is acid-free, 2-component, external-mix acrylic featuring 2 cascading adhesive streams that automatically mix together. Loctite® E-220IC(TM)...

Read More »
Epoxies

Conductive Epoxy Adhesives offer cure times from 7-10 sec.

Featuring thermal stability and chemical resistance, 124-34A/B-187 consists of 2-component syringe dispensable, isotropically electrically conductive, epoxy adhesive, while 125-01A/B-187 offers 2-component syringe dispensable, anisotropically conductive version of product. Cure times as fast as 7-10 seconds can be achieved at elevated temperatures. Applications include assembly of electrical and...

Read More »
Potting Compound has flexible, low-viscosity formulation.
Encapsulants

Potting Compound has flexible, low-viscosity formulation.

Able to be used in thick and thin cross sections, EP30FL epoxy potting and encapsulation compound is 100% reactive and does not contain any volatiles. It cures at room temperature with minimal shrinkage and adheres to similar as well as dissimilar substrates. Recommended for use in environments exposed to thermal cycling, solution can withstand mechanical shock and vibration. Hardened compound...

Read More »
Two-Component Epoxy Adhesive gels in 3 minutes.
Epoxies

Two-Component Epoxy Adhesive gels in 3 minutes.

Used in general-purpose bonding applications or as electrical insulator, Polymer Adhesive EP44 gels in 3 min and cures within a few hours at ambient temperatures to develop bonding shear strength of 3,150+ psi. Parts bonded with this solution can be safely handled within 30 min, and bonds are resistant to thermal cycling as well as chemicals over -60 to 250°F range. Product adheres to...

Read More »
Epoxies

Polymer System suits high temperature bonding applications.

One-component Polymer System EP11HT cures in 110 min at 250°F or 75 min at 300°F. It attains tensile shear strength of greater than 3,300 psi to form rigid and dimensionally stable bonds. Resistant to acids and solvents, service temperature range is -60 to 400°F and it bonds to substrates including metals, glass, ceramics, and plastics. EP11HT is available in pint, quart, 5 gal...

Read More »
Do You Have Unique Lifting Needs?
Sponsored

Do You Have Unique Lifting Needs?

EZRig Cranes offers lifting solutions that are engineered for robust performance, providing the ultimate in portability. Designed for real-world lifting needs, our products are small and light with options and features that make them ideal for a broad range of applications. See our video to learn how an EZRig Crane can simplify your lifting requirements.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers