Epoxies

New Cost Effective, High Conductivity Epoxy
Epoxies

New Cost Effective, High Conductivity Epoxy

HACKENSACK, NJ - Aug 19, 2008 - Master Bond Polymer System EP79 is a novel, cost effective, silver-coated-nickel filled epoxy featuring exceptionally low electrical resistance. Volume resistivity is less than 0.04 ohm-cm at room temperature. EP79 has a convenient 1:1 mix ratio and cures readily at room temperature or more rapidly at elevated temperatures. When cured, it forms strong, tough bonds...

Read More »
Epoxies

Adhesives have operating temperature range of -55 to 230°C.

Offered for variety of application techniques such as screen-printing, pad-printing, stencil application, and B-staged films, 118-06 series of single-component, electrically conductive, epoxy adhesives are also available as adhesive films, pre-cast on release liner at dry thicknesses ranging from 10-125 microns. B-staged adhesive films are already partially cured and can complete cure with exact...

Read More »
Epoxy Adhesive cures in 10-15 min at room temperature.
Epoxies

Epoxy Adhesive cures in 10-15 min at room temperature.

USP Class VI- and FDA-approved, EP41SMED low-viscosity epoxy adhesive has 5:1 mix ratio by weight. Bonds are resistant to water, oil, and many organic solvents as well as cold sterilants, ETO, and gamma radiation. It contains no solvents or diluents, adheres to wide variety of similar and dissimilar substrates, and is available for use in pint, quart, gallon, and 5 gal container kits. Shelf life...

Read More »
Epoxies

Henkel Adhesives and Sealants for Fuel Cell Assembly

MEA-Compatible Adhesive Technologies for Micro-to-Large Fuel Cells Rocky Hill, Conn. - July 17, 2008.... Henkel Corporation (http://www.henkelna.com) has introduced a full line of adhesives and sealants for use on micro-to-large, stationary or portable fuel cells. Henkel products are compatible with membrane electrode assemblies (MEAs) and include structural adhesives for metal and plastic...

Read More »
Epoxies

Epoxy-Based Shed Material suits composite insulators.

Semi-flexible, cycloaliphatic epoxy material Araldite® S-HCEP is designed for producing sheds on reinforced fiber-core composite insulators used in medium- to high-voltage outdoor power applications. It exhibits intrinsic hydrophobicity, hydrophobicity transfer, and recovery. Requiring no stirring, degassing, or pre-heating, erosion resistant epoxy has 1:1 mix ratio by volume, permitting...

Read More »
Resins

How Good Is Your Adhesive?

United Resin Corporation located in Royal Oak, Michigan has been producing epoxy formulations for over 37 years. We have developed a high performance granite and stone edge adhesive called Flex-A-Bond resin and 180 hardener. In its user friendly ratio of 2:1, it produces a tenacious bond, cures quickly, highly polishable, mixes easily with your existing colorants and is water clear. In tests...

Read More »
Epoxy Adhesive Paste resists high temperatures.
Epoxies

Epoxy Adhesive Paste resists high temperatures.

Formulated to cure at room temperature, 2-component Supreme 11AOHT can be applied without sagging or dripping. It has mixing ratio of 1:1, operating temperature of -100 to +400°F, thermal conductivity of 10 BTU/in/ftÂ-²/hr/°F, and dielectric strength of greater than 400 V/mil. Suited for applications involving thermal cycling, product adheres to most metals, ceramics, glass,...

Read More »
Adhesive gels within 45 sec and is cured within 5 minutes.
Epoxies

Adhesive gels within 45 sec and is cured within 5 minutes.

Formulated for general purpose bonding, Type EP50-1 produces high strength bonds with more than 2,000 psi at room temperature that are resistant to thermal cycling and chemicals including water, oil, and organic solvents. Suited for metals, glass, ceramics, wood, and vulcanized rubbers, product is approved for service over temperature range of -60 to more than 250°F. It comes in...

Read More »
Structural Epoxy Anchoring System meets IBC requirements.
Epoxies

Structural Epoxy Anchoring System meets IBC requirements.

Listed as category 1 product for uncracked concrete and dry holes, PE1000+ features 3:1 ratio holding power and meets International Building Code (IBC) requirements for strength design (Cracked Concrete). Dual-component system comes in 13 oz cartridge made from engineered plastic and can be dispensed with manually or pneumatically operated injection tool. Uses include anchoring threaded rod,...

Read More »
Epoxy Adhesive is suited for cryogenic applications.
Epoxies

Epoxy Adhesive is suited for cryogenic applications.

With mix ratio of 100:65 by weight, EP29LPSP can withstand temperatures to 4 K, and resist cryogenic shocks (room temperature down to liquid helium temperatures in 5-10 min time period). It cures at room temperatures, and can be heat cured at 130-165°F for 6-8 hr. Chemical resistant adhesive features mixed viscosity of 400 cps, tensile strength of 6,500 psi, tensile modulus of greater than...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers