End Mills

End Mills

Copy Mills handle close-tolerance machining.

Available in .315-1.250 in. diameters, Series R219.19 Copy Mills offer 2 insert geometries for semifinishing and finishing applications. They use single, precision-ground, ball-nose, replaceable insert, and can ramp into component or drill to shallow depth due to chisel center point. Single-blade unit is suitable for high-speed finishing and general copying of component feature. PVD-coated,...

Read More »
Copy Mills suit die and mold operations.
End Mills

Copy Mills suit die and mold operations.

Designed for roughing, semi-finishing, and finishing operations, ValMILL(TM) V500 Copy Mills utilize RDMT (top form chipbreaker style) or RDMW round inserts. Products are available in 8 end mill sizes that range in diameter from .500-1.5 in. and in length from 4.07-7.44 in. Face mills, available in 5 sizes, are offered in diameters from 2-6 in. End mills use 2 inserts on each cutter, and face...

Read More »
Solid Carbide End Mills are offered in metric sizes.
End Mills

Solid Carbide End Mills are offered in metric sizes.

Engineered for shrink-fit tool holding, 2-flute Metric End Mills feature positive rake angle that supports cutting in soft, medium, and hard materials for side milling and slotting. Cutter diameters range from 0.2-6.0 mm with shank diameter of 6 mm, which is held within -0.0025 to -0.005 mm. Cutter diameter tolerance is +0.000-0.014 mm on sizes up to 3.0 mm and +0.000-0.018 mm on larger sizes....

Read More »
End Mill provides roughing of die and mold steels.
End Mills

End Mill provides roughing of die and mold steels.

HSC Feed is made with sub-micrograin substrate and AL2 plus PVD titanium aluminum nitride coating for wear resistance. With chip loads up to .031 in. per tooth and cutting speeds over 650 sfm, table feeds exceeding 500 ipm are possible. Solid-carbide endmill is suited for P20, H13, and S7 materials with hardness up to Rc 60, as well as carbon steel, alloy steel, cast iron, and stainless steel....

Read More »
Ball-Nose End Mills are designed for punishing cuts.
End Mills

Ball-Nose End Mills are designed for punishing cuts.

Suited for rough milling and semi-finishing operations, ValMILL(TM) V440 Series ball-nose cutters have 2-flute design with one insert per flute and additional insert along tool shank that provides protection for larger cutter diameters. Multi-tooth end mills perform contouring, produce peripheral cuts, slot, drill, and mill die and mold cavities. Products, offered in 6 diameter sizes from .625-2...

Read More »
End Mills remove chips in aluminum applications.
End Mills

End Mills remove chips in aluminum applications.

Blizzard(TM) series end mills feature 2-flute design and are available in regular and stub lengths. Square and various corner radii are also available. End cut gash and offset teeth permit large depths of cut and maximum feed per tooth. With 1 in. dia, end mills deliver clean cuts at feed rates of 450 ipm and speeds of 9,000 rpm. Slotting operations on stub length tools can be performed at axial...

Read More »
Face/End Mills generate 90° square shoulder.
End Mills

Face/End Mills generate 90° square shoulder.

ValMILL(TM) V590 Cutters accommodate ramping and helical interpolation. They eliminate secondary machining operations that are required when producing 90° square shoulders. Nine square shoulder, coolant-thru end mills and 7 face mills are available. Machining speeds of 12,200-40,000 rpms can be obtained depending on tool size. End mills range in diameter from 0.625-1.500 in. with 2-5...

Read More »
Miniature Rib Milling Cutters handle difficult material.
End Mills

Miniature Rib Milling Cutters handle difficult material.

Hanita square- and ball-nosed end mills, designed for mold and die machining, cut materials such as graphite and steels hardened to 60 Rockwell C at speeds to 150 m/min. Offered in 4 series, Diamond Like Coating or TiAIN coatings are available. Hanita Vision end mills, designed for machining hardened steels up to 67 Rockwell C, operate at speeds to 200 m/min. They give surface finish of 63Ra and...

Read More »
Indexable Insert End Mills handle extreme chip loads.
End Mills

Indexable Insert End Mills handle extreme chip loads.

Capable of aggressive material removal, Time-S inserts feature stable, precision-manufactured cutter bodies and inserts with blended double-radius cutting edge. Design provides optimum distribution of cutting forces along entire cutting edge, minimizing vibration and ensuring smooth free-cutting at chip loads of up to .100 in. per tooth. Steel removal rates exceed 150 in.Â-³/min using 80 mm...

Read More »
Indexable End Mills provide aggressive ramping.
End Mills

Indexable End Mills provide aggressive ramping.

Offered in diameters from 0.97 to 8 in., Mill 1 indexable insert end mills are engineered to have consistent and repeatable insert location. Tools are suited for making holes with end mill, eliminating need for multiple drilling and boring operations. Coated grade options include KC725M titanium carbonitride, KC935M aluminum oxide, KC522M titanium aluminum nitride, and KC410M titanium composite.

Read More »

All Topics