Encapsulants

Potting Compound cures quickly in thick applications.
Encapsulants

Potting Compound cures quickly in thick applications.

Trigger Cure(TM) compound cures at room temperature to depths of 1 in. or more, and in areas under components where light does not reach. Two-part compound is applied with typical disposable-tip, static mix dispensers. Exposure to long-wave UV light cures product to depth of 1/4 inch in 20 seconds or less; remaining liquid resin gels in 7 to 20 minutes. Full cure is achieved in 24 hours at room...

Read More »
Coating/Potting Compound coats structural steel columns.
Encapsulants

Coating/Potting Compound coats structural steel columns.

Ceramacast(TM) 589 2-part, silicon-dioxide based, silicate-bonded, chemically-setting ceramic compound is suitable for applications to 2400°F. Dielectric strength and volume resistivity are 100 V/mil and 109 ohm-cm, respectively. Compressive strength is 4,500 psi and coefficient of thermal expansion is 5.5 in./in./°F. Ceramacast(TM) 589 is pneumatically dispensed and reaches full cure...

Read More »
Epoxy Encapsulant is flame retardant.
Encapsulants

Epoxy Encapsulant is flame retardant.

TRA-CAST 9182A medium-viscosity electrical insulator is UL-94 V-O approved. Semi-rigid material adheres to electronic and aerospace-industry materials such as metal, glass, ceramic, industrial laminates, and plastics. It is suited for potting, laminating, transformer encapsulating, filament binding, and coil-embedding applications where stress relief matched with fire retardancy is required.

Read More »
Flame Retardant Epoxy is UL-94V-0 approved.
Miscellaneous Compounds

Flame Retardant Epoxy is UL-94V-0 approved.

Rigid cure epoxy, EP-211FRHTC (Flame Retardant High Thermal Conductivity), offers thermal conductivity and flame retardancy. When cured at room temperature, it has service temperature of up to 130°C. When heat cured, epoxy withstands temperatures up to 200°C. Its viscosity provides penetration and void filling. Electrical potting and encapsulating epoxy reduces operating temperature...

Read More »
Miscellaneous Compounds

Epoxy Compound features one to one mixing ratio.

Type 20-3650 electronic grade epoxy potting, casting, and encapsulating system exhibits excellent physical, thermal, and electrical insulation properties. Tensile strength is 11,000 psi and compressive strength is 15,500 psi. Compound is DOT non-hazardous, easy to mix, and will cure at room temperature or with mild heat. Operating temperature range is -60 to +150°C. Type 20-3650 is suitable...

Read More »
Resins

Encapsulating Resin can cure with several agents.

Electronic grade, casting, potting, and encapsulating epoxy resin system No. 20-365140 adheres to metals, ceramics, and plastics. Physical properties include mixed viscosity of 32,500 cps at 25°C, specific gravity from 1.40 to 1.45 at 25°C, and Shore D Hardness rating of 85 to 88. Tensile Strength ranges from 6,100 to 9,200 psi, and operating temp ranges from -40 to +30 and -65 to...

Read More »
Encapsulants

Plastics Adhesive cures with heat or visible/UV light.

OPTOCAST AC-3801 one-component electronic grade, acrylate based formulation is room temperature stable and free radically initiated. Adhesive/sealant/encapsulant will adhere to polymeric and ceramic substrates when polymerized to flexible solid upon exposure to heat or UV and/or visible light in 320-520 nm range. Cured adhesive offers Shore D hardness of 40 to 45 and temperature range of -40 to...

Read More »
Encapsulants

Conductive Adhesives may replace soldering.

Syon(R) Tru-Bond(R) 206A, 214, 215, and Tru-Cast(R) III electrically conductive adhesives and potting compounds can be used to form conductive paths in applications where hot soldering would be impractical. They also provide thermal conductivity and can be used to bond or seal components or wiring in applications requiring heat dissipation. Low-shrink and nonshrink epoxy and epoxide formulations...

Read More »
Resins

Adhesive/Sealant bonds and encapsulates.

MNRC 04-1347 UV light curing resin is based on aliphatic urethane acrylate monomer blend. At 1 mil thickness, it cures in 10 to 15 seconds with UV light. Transparent liquid is suitable for clear bonds or encapsulation. It bonds to metal, ceramic, glass, and many plastics. MNRC 04-1347 is thixotropic at 25 deg C, and cures to 40-50 Shore A with elongation of 150%. Operating temperature range is...

Read More »
Encapsulants

Encapsulating Elastomers offer hydrolytic stability.

Two-component urethane series encapsulants have durometers from 25 to 55 Shore A. Unfilled materials maintain integrity over operating temperature range of -40 deg to 125 deg C. Glass transition temperature of -72 deg C makes them suitable for low temperature potting applications. They offer electrical insulation, thermal cycling stability, chemical resistance, and no shrinkage. Mixed viscosities...

Read More »

All Topics