EMI / RFI Filters

EMI / RFI Filters

EMI Filter meets military requirements for solderability.

Hermetically sealed on one end for thru-hole sealing between compartments, 9909 Series Spec Mini Solder-in Feed-thru Filter is housed in miniature case measuring 0.140 in. dia (flange) x 0.120 in. dia (barrel) with 0.110 in. body length and total overall length of 0.400 in. including leads. Unit features monolithic discoidal capacitor with capacitance values of 5 pF to .027 Â-µF. Filter is...

Read More »
Three-Phase RF Filters target renewable energy equipment.
EMI / RFI Filters

Three-Phase RF Filters target renewable energy equipment.

Suited for applications with max operating voltage up to 720 Vac, HCWMGF Series comes in 3-phase versions L1, L2, and L3 (without neutral) from 150-2,500 A, with power losses less than 0.02%. Units offer dielectric strength above 3,000 Vdc and insertion loss above 40 dB in entire range, reaching 80 dB between 200 kHz and 1 MHz. With UL94 V2 flammability rating, filters are suited for renewable...

Read More »
Murata Launches World's Smallest 2.4 GHz Balanced Output Filter for Texas Instruments Wireless Connectivity Solutions
EMI / RFI Filters

Murata Launches World's Smallest 2.4 GHz Balanced Output Filter for Texas Instruments Wireless Connectivity Solutions

Hoofddorp, Netherlands: Murata today announced the LFB182G45BG2D280 balanced output matching filter, aimed at a broad range of 2.4 GHz wireless applications using ZigBee® and Bluetooth® low energy technologies. The new filter has been designed specifically for use with wireless connectivity system-on-chips (SoCs) from Texas Instruments Incorporated (TI), the CC253x and CC254x for...

Read More »
EMI / RFI Filters

Common Mode Filters combine EMI filtering, ESD protection.

Supporting data speeds to 3.4 Gbps, silicon-based EMI2121 (single pair), EMI4182, (dual pair) and EMI4183 (triple pair) offer common mode rejection of 15 dB typ at 500 MHz and insertion loss of 1.0 dB typ at 500 MHz. Integrated ESD protection, which meets peak discharge of 15 kV per IEC61000-4-2, and differential mode bandwidth cutoff frequency optimize signal integrity. CMFs protect high-speed...

Read More »
EMC Filters are designed for lift and escalator applications.
EMI / RFI Filters

EMC Filters are designed for lift and escalator applications.

Designed for lifting equipment and machines with variable speed, such as elevators or escalators, FVDB series offers ratings from 7-250 A and can operate in applications with nominal voltages of 520 Vac 50/60 Hz; 720 Vac version is also available. Products are built according to EN60939 and UL1283 standards and satisfy 2004/108/EC directive, according to EN12015:2005 standard, for EMC conductive...

Read More »
EMI Line Filters come in 3 design configurations.
EMI / RFI Filters

EMI Line Filters come in 3 design configurations.

Intended for 1-phase systems, Series FMBB NEO is characterized by high symmetrical and asymmetrical attenuation. Design C attenuates potentially strong conducted interferences, while Design D is laid-out for attenuation of high frequency interferences, and Design F is suited for low frequency noise attenuation. Family is rated 1-36 A, according to IEC and 125/250 Vac, 1-30 A according to UL/CSA....

Read More »
EMC Filters are suited for PV inverters up to 1,500 A.
EMI / RFI Filters

EMC Filters are suited for PV inverters up to 1,500 A.

Installed between PV inverter and solar panel, FEDC series allows EMC standards compliancy for entire PV system and helps prevent pre-mature panel aging. Series is designed to reduce conducted emissions towards solar panel and reduce EMI radiations from solar panel, increasing solar panel lifetime and installation service life. Ratings range from 25-1,500 Adc; up to 150 Adc without terminals and...

Read More »
EMC Filters are designed for PV inverters up to 1,500 A.
EMI / RFI Filters

EMC Filters are designed for PV inverters up to 1,500 A.

Installed between inverter and solar panel, FEDC series ensures compliance with EMC standards for entire PV system by reducing conducted emissions towards solar panel and EMI radiations from solar panel. Product is available with ratings from 25-1,500 Adc, without terminals up to 150 Adc, and with screw connections up to 1,500 Adc. While meeting EN60939, UL1283, and RoHS requirements, series has...

Read More »
Feedthru Filters address automotive EMI concerns.
EMI / RFI Filters

Feedthru Filters address automotive EMI concerns.

Featuring miniature surface mount design, LC T configured FeedThru Filters provide design engineers with consistent broadband EMI filtering for critical drive by wire applications such as throttle and braking. AEC Q200-qualified units typically provide -30 dB of attenuation across 300 MHz frequency spectrum. Response can start as low as 75 MHz or end as high as 1,500 MHz. Current ratings range...

Read More »
Tekna Manufacturing LLC Announces NFPA 99 Compliant Model 7200 Multiplace Chamber
Sponsored

Tekna Manufacturing LLC Announces NFPA 99 Compliant Model 7200 Multiplace Chamber

Tekna is a leader in Monoplace and Multiplace Hyperbaric Chambers for Hyperbaric Oxygen Therapy (HBOT), offering products that set the standard for quality and innovation. Our new 7200 series of multiplace chambers is a state-of-the-art system that integrates advanced engineering with a plethora of features and options making it the industry's premier HBOT system. To learn more, see our video.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers