MOSFET Driver delivers 5 A for buck/boost DC/DC converters.
Operating from supplies up to 38 V, LTC4447 drives upper and lower power N-Channel MOSFET gates from rail-to-rail over 4-6.5 V range in synchronous rectified converter topology. It sinks up to 5 A, sources up to 3.2 A, and can also drive multiple MOSFETs in parallel for higher-current applications. Along with integrated bootstrap Schottky diode, features include adaptive shoot-through protection,...
Read More »MOSFET Pre-Driver IC targets motor system designers.
Available in 48L eLQFP package, Model A4935KJP-T is suited for systems that use sinusoidal control of motor phase currents. Automotive grade 3-phase MOSFET pre-driver IC integrates regulating charge pump that provides full gate drive capability for battery voltages down to 7 V and reduced gate drive for battery voltages as low as 5.5 V. It features fault diagnostics and reporting to decode and...
Read More »MOSFET Gate Drivers are optimized for switching efficiency.
Available in 8-lead SOIC and 10-lead DFN packages, ISL6615 and ISL6615A have 4 A source and sink gate drive currents for UGATE and 4 A source with 6 A sink on LGATE to reduce gate voltage rise and fall times. This minimizes switching losses and promotes efficiency. Both models also support 9.6 and 12 V input rails, and designers can choose versions which support 3.3 V PWM signals (ISL6615) or 5 V...
Read More »
MOSFET Drivers are rated for peak output current of 1.5 A.
Inverting MCP1415 and non-inverting MCP1416 MOSFET drivers are rated for peak output current of 1.5 A over operating voltage range of 4.5- 18 V. Both devices exhibit latch-up immunity and are available in miniature 5-pin SOT-23 package. Small package size allows designers to position gate driver close to MOSFET's physical gate connection, minimizing gate bounce, rise-and-fall times,...
Read More »
Medical Sealing Solutions: Protecting Devices & Equipment from Contamination
This white paper provides an in depth look into medical sealing solutions for protecting devices & equipment from contamination.
Read More »IGBT Driver offers individual control parameter settings.
Suitable for 1,200 and 1,700 V IGBT modules, RoHS-compliant SKYPER-® 52 allows for transmission of isolated sensor signals and individual protection level settings. Use of differential digital signal processing enables switching characteristics, shut down levels, and error processing to be set to meet application requirements. Dual 9 W output channels and peak gate current up to 50 A make...
Read More »Isolated Gate Drivers feature programmable dead time.
Occupying 200 mm-², Si823x ISOdriver Series integrates 2-channel isolator and dual driver into single chip. High-side, low-side, 4 A units feature propagation delay of 50 ns, optimizing timing margins and control response. Because devices are designed in CMOS, they do not suffer from performance drift over time and temperature. Integrated under-voltage lock-out circuitry prevents erroneous FET...
Read More »SiGe Chipset delivers 4 x 10 Gbps for optical interconnects.
Comprised of 4 x 10.3 Gbps Transimpedance Limiting Amplifier (HXR4104) and 4 x 10.3 Gbps Vertical Cavity Surface Emitting Laser driver (HXT4104), HXR/T4104 chipset is fully programmable via 2-wire interface. This enables control of signal peaking, modulation, and average currents while also providing access to temperature and output power monitoring on channel-by-channel basis. Parallel VCSEL...
Read More »
Single-Phase High-Voltage ICs suit motor drive applications.
Available in 8-lead SOIC, IRS260xD Series power MOSFET and IGBT drivers are designed for sinusoidal and trapezoidal motor control. Model IRS2607D high- and low-side driver features outputs in phase with inputs. With 540 nsec internal dead-time, IRS2608D half-bridge driver offers high-side output in phase with HIN input and low-side output out of phase with LIN input, while IRS2609D features...
Read More »MOSFET Driver features 100 V maximum supply voltage.
Series LTC4446 can drive upper and lower N-Channel power MOSFETs in 2-transistor forward converter. It can source up to 2.5 A with 1.2 W pull-down impedance for driving top MOSFET and 3 A with 0.55 W for synchronous MOSFET. Unit can also drive multiple MOSFETs in parallel for higher current applications, and features rise/fall time of 8/5 nsec top MOSFET and rise/fall time of 6/3 nsec bottom...
Read More »
MOSFET Driver features up to 200 V bridge supply voltage.
Suited for use in Class-D audio amplifiers, Model MD7120 provides 12-200 V output, -
Read More »
Ensure Your Medical Device Meets Regulatory Standards with Triad's Custom Magnetics
Triad Magnetics' custom components for medical devices are designed and manufactured with the strictest regulatory standards in mind. Our capabilities include rapid design, prototyping, and testing of inductors, transformers, and power supplies for medical equipment. Check out our video to learn more.
Read More »
