Electronic Drivers

MOSFET Driver targets high-voltage LED designs.
Electronic Drivers

MOSFET Driver targets high-voltage LED designs.

Featuring 12 nsec propagation delay and 2 A drive capability, Model MAX15054 is suitable for high-brightness LED designs that require buck or buck-boost topology but lack high-side MOSFET driver. Dual UVLO feature protects power MOSFET from damage in event that gate-drive or supply voltage is too low. Housed in 2.9 x 2.8 mm, 6-pin SOT23 package, driver operates up to 60 V and is specified over...

Read More »
Electronic Drivers

PWM-Capable LED Driver ICs suit photo flash applications.

Supplied in 8-pin, 2 x 3 x 0.8 mm TDFN package and requiring 3 external components, LDS8640/41/80/81 are 2-channel, charge-pump based LED drivers that provide full output power from single-cell lithium ion battery or 2.7-5.5 V supply. Channels in LDS8680 can drive one HB LED each up to 800 mA and 400 mA or used concurrently to drive 2 HB LEDs at 400 mA each. Similarly, LDS8640 drives one channel...

Read More »
MOSFET Driver supports buck or boost DC/DC converters.
Electronic Drivers

MOSFET Driver supports buck or boost DC/DC converters.

Operating from up to 38 V supply, synchronous Model LTC4449 drives upper and lower N-channel MOSFET gates over range of 4-6.5 V. Unit can sink up to 4.5 A and source up to 3.2 A. Adaptive shoot-through protection prevents upper and lower MOSFETs from conducting simultaneously while minimizing dead time. Housed in 2 x 3 mm DFN-8 package, IC features 3-state PWM input for power stage control and...

Read More »
Electronic Drivers

Single-Ended to Differential Amp drives 16-18 bit SAR ADCs.

Supplied in 8-lead MSOP and 3 x 3 mm DFN packages, LT6350 is 33 MHz rail-to-rail input and output ADC driver that settles to 16 bits in 350 ns. Each of 2 internal op amps achieves 1.9 nV/√Hz input-referred noise density, resulting in 8.2 nV/√Hz total output-referred noise. Operating on 2.7-12 V supply and consuming 4.8 mA, driver enables ADCs to achieve better than 110 dB SNR over 1 MHz...

Read More »
Electronic Drivers

LED Driver targets general illumination products.

Housed in low-profile DFN package, 1 A linear mode, constant-current Model DLD101 is suitable for flashlights and lighting in emergency, garden, and poolside applications. By integrating base accessible pre-biased transistor, LED driver incorporates biasing resistors on chip, so LED current is set via single external resistor without additional boost resistor. For pass element, high drain current...

Read More »
Electronic Drivers

White LED Driver IC features LED current and timing control.

Designed for LCD TVs, Models AAT2400/2401 are master/slave devices that operate from regulated 12 or 24 Vdc power supply. AAT2400 supplies 40 V rail to drive 10 series LEDs with typical VF of 3.6 V with up to 100 mA. Sixteen current sinks split between master and slave devices provide constant current drive for up to 160 white LEDs. Eight-bit dot correction register compensates for variations in...

Read More »
Motor Driver IC is automotive-qualified.
Electronic Drivers

Motor Driver IC is automotive-qualified.

Enabling control of parameters via SPI interface, ASSP E910.87 EC motor driver is designed for automotive or industrial applications with voltages between 4-27 V. Gate driver IC for 6 NMOS FETs allows driver outputs to be controlled at up to 60 kHz. Integrated voltage regulator can power small microprocessors directly. Protective features include phase shortcut, gate shortcut, cross conduction,...

Read More »
Integrated IBGT Ignition Driver optimizes automotive ignition.
Electronic Drivers

Integrated IBGT Ignition Driver optimizes automotive ignition.

Specified over -40 to +140°C range, E91.89 is supplied in SOIC 8N package, integrates internal slew-rate control as well as programmable soft turn-on/switch-off functions, and operates from 6-26 V supply. Corresponding to input control signal, product drives IGBT which provides current to ignition coil. Together with ignition coil and ignition IGBT, it is integrated into compact module...

Read More »
Electronic Drivers

Clock Network Manager has 8 programmable output banks.

As flexible clock network management device, UT7R2XLR816 offers independent bank programmability for frequency, I/O type, polarity, skew, and voltage. It supplies up to 16 clock outputs over 8 banks, with independent power supplies for each. Outputs can be configured as LVCMOS or standard LVDS pairs, and phase is adjustable with respect to reference clock. Other characteristics include less than...

Read More »
Electronic Drivers

Power/Display Optimizer extends portable device battery life.

Implemented in portable elecronic devices, Intelligent Display Power Optimizer (DPO) Proven System Block (PSB) works in conjunction with Visual Enhancement Engine (VEE(TM)) v2.0 to deliver TV-quality viewing experience and up to 80% reduction in backlight power usage. Single-chip solution's VEE examines video bit stream in real-time, on pixel-by-pixel basis, and also runs comparative algorithms...

Read More »
Precision Machined Parts for High Tech Applications
Sponsored

Precision Machined Parts for High Tech Applications

For precision and value that sets the standard for quality and craftsmanship, EGS Production Machining is the source for precision and value. Our extensive capabilities and dedication to customer service allow us to deliver the optimal manufacturing solution. See our video to learn more.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers