Frequency Converter features SERCOS interface.
System200 REFUdrive comprises modular construction kit of drive and control components that use universal, open standards. SERCOS interface expands existing options for connection to Profibus DP, Interbus S, and CANopen. Output ratings from 1.5 to 600 kW allow decentralized drive structures with servo drives and frequency converters. REFUdrive meets class A standards for compatibility. Drive...
Read More »
Synchro to DC Converter operates at 400 conversions/sec.
Miniature (1.5 cu. in) solid-state Series SD109 converts 3-phase synchro or 2-phase resolver inputs into sine and cosine outputs. Peak angular error is rated at Ã-
Read More »
Converters require no external transformers.
PC104 Series consists of 3- and 4-channel PC/104 and compatible Synchro, Resolver, and LVDT/RVDT to digital converters employing type 2 ratiometric tracking converters. They accept any group of up to 4 individual, 3-wire Synchro, or 4-wire Resolver inputs, or 2-4 wire LVDT/RVDT inputs; over frequency range of 50 Hz to 10 kHz, and convert them into 10-16 bit words of natural binary data...
Read More »
PCI A/D Board captures data at 600 kHz per channel.
Series PCI-417 handles 16 analog input channels in parallel, with 12-bit A/D resolution. Non-stop streaming design collects gigabytes to memory or disk. Board has 32-bit wide on-board DMA PCI bus master that offloads host CPU. Features include 2 streaming 16-bit analog output D/A channels, 24 bit digital I/O, and local A/D FIFO memory up to 256 Ks to avoid WindowsÃ-® delays. Models available...
Read More »
Industrywide Applications for Deep Drawn Metal Stamping
Deep-drawn metal stamping applies a significant punching force to radically draw metal sheets into a die cavity. Finished components produced by this process tend to have a depth that exceeds their diameter, which is why manufacturers refer to it as "deep-drawn" metal stamping.
Read More »
Converters offer 16-bit resolution and +/-.005 deg accuracy.
Synchro to Digital Converters are designed to convert 2-speed Synchro or Resolver inputs of 11.8 V, 26 V, 90 V 400 Hz, or 90 V 60 Hz into 16-bit parallel binary outputs respresenting angle. Speed ratios of 1 x 10, 1 x 18, 1 x 36, 1 x 8, 1 x 16, 1 x 64, and 1 x 128 are available. Converters track rates up to 1000 deg/sec. They have DC velocity output and built in test (BITE) with digital...
Read More »
Synchro To BCD Converters mount on PC boards.
SBC40 series converts synchro or resolver inputs of 11.8 or 90 V at 400 Hz into 3 or 4 decade BCD data representing angle with accuracy of Ã-
Read More »
TTL and 24V Converters contain two independent channels.
Model 8501 two-channel 5 to 24 V converter requires 7 mA into 382 ohms per channel to provide 7 mA output into the 3 Kohm, 24 V typical PLC logic input. They may be driven by TTL logic, H series TTL logic, or with open collector NPN transistor. Input frequency is DC to 15 KHz. Model 8502 two-channel 24 to 5 V converter requires 7 mA into 2.5 Kohm per channel to provide 5 mA sinking output to TTL...
Read More »A/D VME Board handles high frequency applications.
Model 6802 has 32 channels of delta sigma A/D conversion with extremely precise, linear-phase low pass filtering. Each A/D has 24 bits of resolution at sampling rates from 1 kHz to 216 kHz. Front-panel sync input signal allows synchronization of multiple 6802 boards. Outputs of up to eight 6802 boards, for maximum of 256 channels, can be combined over single FPDP cable. Data tagging is also...
Read More »Transmitters convert analog input signals to digital data .
DIN-100 Sensor to Computer Modules transmit data via RS-485 to controller, which may be computer or other processor-based equipment. Modules measure temperature, pressure, voltage, current, digital input, or digital output signals. They perform all signal conditioning, scaling, linearization, and conversion to linearized ASCII data values or Modbus RTU data values. Address, baud rate, parity, and...
Read More »
Air To Electronic Converter displays air gage signals.
Compact VE-03 mounts as free-standing unit to standard DIN rail. In operation, air input signal is received in front of converter through air adapter. Output signal is transferred to electronic column or gage computer from signal output socket at back of unit. Zero and gain controls on front of converter adjust electric signal. Zero control is used for adjusting zero point on electronic column...
Read More »
What Can Test Devices Spin for You?
Test Devices helps you ensure the safety and efficiency of your high performance machines with cutting edge spin testing, rotor engineering, and precision balancing capabilities. Check out the video to learn more.
Read More »
