Electronic Converters

Electronic Converters

Analog-to-Digital Converter provides RF sampling at 4 GSPS.

Measuring 9 x 9 mm, 12-bit Model ADC12J4000 supports JEDEC JESD204B serial interface standard for data converters up to 8 Gbps, while consuming 1.9 W of power. Device combines giga-sample ADC IP with low-power digital processing blocks that provide digital filtering and down conversion. IC can perform external signal conditioning typically handled by FPGA at total decimation of 4/8/10/16/20/32x,...

Read More »
Analog-to-Digital Converters (12-bit) offer 5 analog input ranges.
Electronic Converters

Analog-to-Digital Converters (12-bit) offer 5 analog input ranges.

Offering 8 Â-µsec conversion time, ADC-85 series comes in hermetically sealed, 32-pin, side-brazed DDIP or gull-wing SMT ceramic package. Each unit features ½ LSB linearity and is 100% tested for performance across one of 3 temperature ranges: 0 to +70°C, -40 to +100°C, and -55 to +125°C. Along with parallel and serial digital outputs, units feature...

Read More »
Electronic Converters

High-Resolution ULP SAR ADCs consume 5.5 mW at 1 MSPS.

Available in 10-pin, 3 x 4.9 mm MSOP and 3 x 3 mm QFN package options, single-channel ADC8881 series includes 18- and 16-bit SAR (successive approximation register) ADCs with speed options from 100 kSPS to 1 MSPS. Input common-mode range simplifies signal conditioning andÂ- helps digitize difference between 2 independent sensor signals with widely varying common-mode voltage...

Read More »
Electronic Converters

Current to Voltage Converter is ready for analog ASIC integration.

Using Transimpendance Amplifier architecture with 8 digitally programmable current ranges from 8 Â-µA to 1 mA, SCi310 Analog Front End IP block converts current captured from sensor system to fully differential output voltage that is ready to be amplified. Precision I/V converter block maintains constant voltage at input pin for all operating modes and input currents while enhancing...

Read More »
Electronic Converters

JESD204B-Compatible, 16-bit DAC runs at up to 2.5 GSPS.

Suited for multimode 2G/3G/4G cellular base stations,Â- 2.5 GSPS DAC38J84 (4-channel) supports JEDEC JESD204B serial interface standard for data converters up to 12.5 Gbps. Pin-compatible 16-bit DAC38J82 (2-channel) runs at 2.5 GSPS. Dual independent transmit paths of DAC38J84, which also integrates multi-band summation block, provide up to 1 GHz of complex information bandwidth...

Read More »
Electronic Converters

Signal Converter offers dimming control for 80 fixtures.

Extracting dimming levels and address information from incoming DALI data, Model DAP-04 controls each of 4 PWM dimming outputs individually. Each channel can drive PWM input of any MEAN WELL LED power supply equipped with 3-in-1 dimming function. Model DAP-04 offers 1–100% dimming range, and choice of linear or logarithmic dimming curves which comply with IEC62386-207. Built-in relay and...

Read More »
Electronic Converters

Discrete Serial Link Aggregator ICs support data rates to 10 Gbps.

Using 2 power rails, 1- to 8-channel TLK10081Â- and 2-channel TLK10022 aggregate and de-aggregate point-to-point serial data streams for transmission over backplanes, copper cables, and optical links. Features include intelligent serial link switching and built-in digital equalization. While TLK10022 supports 4:1, 3:1, and 2:1 bidirectional serial link configurations, TLK10081...

Read More »
Electronic Converters

A/D Converters support multi-channel data acquisition.

Integrating 16 channels into single package, Model AD9249 dissipates 58 mW of power per channel at 65 MSPS, while 8-channel Model ADS9681 dissipates 110 mW per channel at 125 MSPS. Both 14-bit units are available in 10 x 10 mm packageÂ- with on-chip sample-and-hold circuit. DACs achieve spurious free dynamic range greater than 90 dBc and signal-to-noise ratio of 74 dBFS or...

Read More »
HP Fiber to RS232 Converter offers 120 Kbps data transfer rate.
Electronic Converters

HP Fiber to RS232 Converter offers 120 Kbps data transfer rate.

Providing electrical-to-optical and optical-to-electrical conversion, Model 4139 is used to connect fiber optic linked terminals to controller with RS232 interface port. Unit uses DB9 connector for RS232 connection and provides full galvanic isolation between connected devices. Maximum link distance is greater than 1,640 ft with 2.00 mm hard clad silicon fiber cable. Measuring 5.5 x 2.25 x 1.0...

Read More »
Electronic Converters

Amphenol Aerospace Operations (AAO) High Speed Solutions (HSS) Division Offers Rugged Copper to Fiber (CTF) Media Converter Products

Amphenol now offers rugged CTF media converters from DC to 10Gbps supporting multiple protocols for the military, aerospace and industrial markets. SIDNEY, N.Y. - Amphenol Aerospace (NYSE: APH), a global leader in interconnect technologies, now offers additional Copper to Fiber Media Converter products.Â-  These assemblies are designed for military and aerospace environments. AAO HSS has...

Read More »
Tekna Manufacturing LLC Announces NFPA 99 Compliant Model 7200 Multiplace Chamber
Sponsored

Tekna Manufacturing LLC Announces NFPA 99 Compliant Model 7200 Multiplace Chamber

Tekna is a leader in Monoplace and Multiplace Hyperbaric Chambers for Hyperbaric Oxygen Therapy (HBOT), offering products that set the standard for quality and innovation. Our new 7200 series of multiplace chambers is a state-of-the-art system that integrates advanced engineering with a plethora of features and options making it the industry's premier HBOT system. To learn more, see our video.

Read More »

All Topics