Flexotherm-® Launches New Line of Continuous Emission Monitoring Products
Flexotherm is extending its line of quality electrically-heated products into stack testing. Their proven expertise in emissions testing has enabled this transition into the growing field of Continuous Emission Monitoring Systems (CEMS). Stack or source testing is an important tool in monitoring a facility's compliance with EPA emission requirements in accordance with the Clean Air Act....
Read More »Op-Amp enables low power consumption in portable designs.
Supplied in 5-pin SC-70 package, FAN4931 operational amplifier (op-amp) helps extend battery life and conserve board space in portable and consumer designs. It consumes 200 Ã-µA of power and, with common mode voltage range extending beyond positive and negative rails, promotes design flexibility. Operation from 2.5-5 V accommodates needs of portable and consumer products such as sensor...
Read More »
Test Points come in 10 colors.
Designed to replace wire-wrap posts and turret terminals, Test Points come in Brown, Green, Blue, Purple, and Gray, as well as Red, Black, White, Yellow, and Orange. All may be used on .062 and .093 thick PCBs with variety of gripping devices, including J-hooks, EZ-hooks, grabbers, alligator clips, tips, and probes. Designs also serve to keep onboard terminals perpendicular to PCB so that...
Read More »Analog-to-Digital Converter dissipates only 89 mW.
Operating from 1.8 V analog supply, 16-bit no missing codes Model LTC2259-16 offers signal to noise ratio performance of 73.1 dB and SFDR of 88 dB at baseband. Digital outputs can be set to full rate CMOS, DDR CMOS, or DDR LVDS. Separate output power supply allows CMOS output swing to range from 1.2-1.8 V. Housed in 6 x 6 mm QFN package, 80 Msps device includes alternate bit polarity mode and...
Read More »
TOP 3 SEAL TROUBLE SIGNS and HOW TO FIX IT
If ignored, broken seals can lead to a loss in production and equipment shut down. For more information on seals and seal repairs, download now.
Read More »Power Management and Audio ICs increase operational efficiency.
Extending battery life for music-enabled devices, DA9057 integrates dual-input switching USB power manager/Li-ion battery charger, true-ground Class G headphone driver, and 5 programmable DC/DC converters. Latter optimally supports 24-bit stereo audio headphone playback on 5 mW power budget. Also available, DA7201 is 3 W mono audio power amp capable of driving 4 ohm speaker loads. Its 1.5...
Read More »
Current-Sense Amplifier offers low power consumption.
Offering 1.6 to 28 V input-voltage range, Model MAX9634 current-sense amplifier features 1 Ã-µA quiescent current with Ã-
Read More »
Media Processor delivers online HD video with single chip.
Allowing playback of 1080p HD video content, VIA VX900 Media System Processor features VIA ChromotionHD v2.0 video engine that supports H.264 codec. Unit features acceleration for MPEG-2, MPEG-4, and WMV formats as well as dual-channel support for DisplayPort, HDMI, DVP, VGA, and LVDS/TMDS. Measuring 31 x 31 mm, it includes VIA Chrome9(TM) HCM 3D graphics core and 128-bit 2D engine. Product also...
Read More »
Magnetic Latching Solenoids offer stroke lengths to 3 in.
Available in package sizes from 3/8 to 3Ã-½ in. diameter, Bi-Stable Latching Solenoids come in rotary and linear designs with response time in milliseconds. Single voltage pulses open and close armature resulting in minimal heat rise and no holding power. By utilizing permanent magnet on solenoid pole face, once air gap is closed, solenoid stays in closed position until pulsed in reverse...
Read More »
Relay Controller Board supports several wiring combinations.
Featuring 6 contact support as well as differential and dual differential multiplexing, model IA-3154-2 is 24 DPDT relay controller board which includes commands for single and twin relay operation and is supported by Series-3000 controlling commands list. Board supports daisy-chain operation, with buffered communication output port enabling numerous boards to be chained and connected to common...
Read More »
In-Line Wire Connector is designed for pre-fab operations.
Providing crimp-free, push-in butt splice, SpliceLine(TM) has 2 ports to support solid- and stranded-wires ranging from 12-20 and 12-16 AWG, respectively. It is precision-molded from transparent polycarbonate, permitting visual inspection of connections. Due to ultra-slim profile, unit can be used to lengthen wires in tight spaces, while multiple connectors can simultaneously pass through Ã-½...
Read More »
SEALTITE® Fittings and Cord Grips Offer Longer Lasting Protection
Anamet Electrical's 316 Stainless steel SEALTITE® fittings and UL-listed cord grips protect sensitive wiring components from fluids, corrosive contaminations, bumps, and abrasions with a steel core and liquid tight conduit jacket. Check out this video to learn more.
Read More »
