Electronic Components & Devices

Display Console houses multiple monitors.

Display Console houses multiple monitors.

Modular Profile(TM) Flat Panel Display System consists of interactive desk and console system that permits maximum screen viewing while minimizing floor and vertical space requirements. It supports 1,200 lb of components and IT gear, has adjustable arm mounts to provide ergonomic positioning, and routes all cabling and power cords. Applications include network operation centers, security, command...

Read More »

A/D Converters sample images at high speeds.

SPT7864 and SPT7866 10-bit CMOS analog-to-digital converters sample at 40 and 60 MSPS, respectively, making them suitable for CCD imaging, video digitizing, and medical imaging applications. Both have good linearity, including DLE of ±0.5 LSB and ILE of ±0.6 LSB at full sampling speed. They have built-in sleep mode with typical power dissipation of 55 mW, and both allow user to choose between...

Read More »
Inductors feature lead-free terminations.

Inductors feature lead-free terminations.

Surface mount, wire-wound CC Series Inductors are used for RF applications in electronics industry, especially for wireless and test and measurement equipment where solderability is concerned. Models CC0603, CC0805 and CC1008 have inductance ranges of 1.6 to 270 nH, 3.3 to 820 nH, and 10 to 4700 nH, respectively. Model CF1008 is available for applications requiring inductance from 1.2 to 10 mH.

Read More »
Elastomeric Couplings feature 347 cast stainless steel ring.

Elastomeric Couplings feature 347 cast stainless steel ring.

Jaw In-Shear (JIS) 6-Pin elastomeric couplings are non-lubricated, drop-in replacements for grid spacer couplings. Converting to in-shear service doubles standard Jaw Coupling's angular misalignment capability to 20 and its parallel misalignment capability to 0.030-0.094 in., depending on size. Units fill BSE (Between Shaft End) gaps of 3.5, 5, 7, and 9 in., with maximum bores up to 5.5 in.,...

Read More »
Multiple Chip IRED provides total output power of 6.0 mW.

Multiple Chip IRED provides total output power of 6.0 mW.

CLE400F-905 4-leaded device contains three 905 nanometer IRED chips mounted in flat leaded PLCC package. Chips feature current III-V solid state technology with transparent gallium aluminum arsenide windows. Chips are wire bonded in parallel and overcoated with clear epoxy, which provides emission angle of ± 70° at half power points. Maximum operating temperature with clear epoxy lens is 100°C.

Read More »
Stacked LED Assembly retrofits to current set-ups.

Stacked LED Assembly retrofits to current set-ups.

Multi-stack LED assembly allows custom configuration of LEDs stacked 1, 2, and 3 high, with spacing up to 6 in. wide, without special tooling. Operators can install from 6 to 36 LEDs at once in complex configurations. All LEDs have proper viewing angles, correct sequencing and polarity, and consistent color matching. Assembly also provides resistance to shock and vibration. It is made from UL...

Read More »

Filter Card provides DC offset compensation.

AAF-2, 2 to 8 channel, tunable low-pass filter features selectable frequency ranges in Butterworth, Bessel, Cauer, or Linear Phase characteristics that eliminate noise and alias errors while providing DC and Gain accuracy for 16-bit data acquisition systems. Filter channels are fully isolated from PCI bus, and are continuously tunable from 0.1Hz to 200kHz. Input and output range is up to ±l0V...

Read More »

CDMA Filter handles high data rates.

Miniature Model CER0059A receive, ceramic, monoblock filter, for North American PCS applications, measures 7 x 5.5 x 3.8 mm, making it suitable for most space-limited designs. It can be used for high data rate (HDR) wireless modem terminals in laptops, PDA's and handsets using 2.5G and 3G CDMA lx technology.

Read More »
RS-422/485 Card operates at speeds to 18 Megabaud.

RS-422/485 Card operates at speeds to 18 Megabaud.

CYB 218MP dual-port PCI RS- 422/485 card can be set for communication rates from 115,000 to 18,000,000 baud. Two ports on each card can be set independently for either full or half-duplex RS-485 operation. Card does not rely on host PC to track transmissions; on-board circuits track beginning and end of all incoming and outgoing messages. Handshaking circuit synchronizes card with each...

Read More »

All Topics